说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 种仁
1)  Kernel [英]['kɜ:nl]  [美]['kɝnḷ]
种仁
1.
Studies on Dynamic Characteristics of Nutrition content of Corylus avllana L.Kernel during Seedling Stage;
欧洲榛子苗期种仁营养变化特点研究
2.
To screen the specific genes in the kernel of peanut,a differentially expressed cDNA library was constructed by using suppression subtractive hybridization(SSH).
应用抑制消减杂交技术,以花生种仁cDNA作为消减杂交的试验方(tester),以花生果皮cDNA作为驱动方(driver)进行消减杂交。
2)  Seed [英][si:d]  [美][sid]
种仁
1.
The Analysis of Nutrient Substances in 34 Common Almond Seeds at Home and Abroad;
34个普通扁桃种仁营养成分分析
2.
Different characteristics of stone and seed such as seeded stone vs.
枣核是鉴定品种的重要特征,对冬枣、榆次团枣、婆婆枣、紫圆枣等37个枣品种和1个毛叶枣品种台湾青枣的果核和种仁的外部形态指标进行了详细地描述和测量,以研究枣不同品种果核、种仁各数量指标间的相关性,得出核纵径和核喙长的线性方程Y=-0。
3)  seed kernel
种仁
1.
The nutrition composition in the seed kernel of white pitaya was analyzed.
对火龙果种仁的营养成分进行了分析 。
4)  seed oil
种仁油
1.
The analysis and preparation condition of squalene in Siraitia grosvenorii seed oil by HPLC are estabilished in this thesis,the following HPLC conditions are the best:column:Shodex Asahipak C_(18) column;mobile phase,V(acetonitrile)∶V(methanol)=60∶40;detection wavelength,203nm;flow rate,2ml/min;tmperature,40℃.
采用高效液相色谱法分析测试罗汉果(S ira itia g rosvenor ii)种仁油中的角鲨烯,确立色谱条件为:色谱柱:Shodex A sah ipak C18,流动相为甲醇/乙腈=60/40、检测波长为203nm、流速为2m l/m in、柱温为40℃。
2.
The seed oil of palm(Trachycarpus fortunei) harvested from two sampling places of West Hunan province was extracted by supercritical CO2 fluit extraction technology,and its components was analyzed by GC-MS.
利用超临界CO2流体萃取技术提取了湘西地区两个采样点的棕榈树种仁油,并对其化学成分进行了气相色谱质谱联用(GC-MS)分析。
5)  Kernel percentage
种仁率
6)  fruit kernel
荔枝种仁
1.
The results in the laboratory indicated that one generation of Conopomorpha sinensis Bradley could be successfully reared,using litchi fruit kernel as food.
室内试验结果表明,利用荔枝种仁作为食物成功饲养荔枝蒂蛀虫至完成一世代。
补充资料:皂化溶解油、肥皂油和调水油
分子式:
CAS号:

性质:又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂(如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂)和少量稳定剂(如乙醇或甲醇)而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主,润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条