1) Overying concentration caprock
上覆浓度盖层
2) overlying caprock
上覆盖层
3) concentration caprock
浓度盖层
1.
Determining forming period of restrained seal action of undercompacted concentration caprock by using interval travel time data and its research meaning.;
利用声波时差资料研究欠压实浓度盖层抑制封闭作用形成时期及其研究意义
4) cover thickness
覆盖层厚度
1.
The determination of the cover thickness of the submarine tunnel is very important,because it will be very dangerous if the cover thickness is too small,whereas the length,slope gradient and cost will be increased after a larger cover thickness is chosen.
江底隧道的覆盖层厚度十分重要。
2.
In underwater tunnel construction,the cover thickness not only plays the decisive role in its security,but al- so is a leading factor determining the underwater tunnel s cost and length.
在水下隧道施工中,覆盖层厚度不仅对其安全性起着决定性作用,而且还是决定水下隧道造价和长度的主要因素。
3.
In underwater tunnel construction,to confirm the reasonable cover thickness is the key in the technology.
合理的确定水下隧道覆盖层厚度是建设水下隧道关键技术之一。
5) Overburden thickness
覆盖层厚度
1.
The method can determine the overburden thickness based upon the electricity difference between overburden and lower datum rock, and is one of the most valid method with high-efficiency, depth and accuracy for ground electricity section imaging in hydrogeology and engineering geology.
这里简要阐述了高密度电阻率法发展过程、勘探原理、野外工作方法,并将该方法应用到水电站选址覆盖层厚度探测中,获得了测区部位的视电阻率二维成像图。
2.
12 construction schemes are constituted according to the space temporal relationship between construction steps,the excavating method,the length of drivage cycle,the space distance among each working face and the overburden thickness of each tunnel.
根据各条隧道开挖支护施工步的空间时间关系、工作面开挖方法、掘进进尺、各掌子面空间间距和覆盖层厚度等多种因素制定12种施工方案并用FLAC3D进行相应的三维数值计算。
6) Canopy cover degrees
冠层覆盖度
1.
Canopy cover degrees had a outstanding positive linear correlation to tuber expansive speeds.
根系拉力与冠层覆盖度及块茎产量均呈极显著正相关，即根系拉力越大，冠层越旺盛，块茎产量越高。
补充资料：有机覆层:有机覆层
在基体材料表面覆以有机材料的材料保护层。在机械製造中﹐有机覆层的绝大部分是涂装层﹐或称油漆层。此外﹐也有用橡胶或塑料作为覆层的。需要抗酸﹑硷和抗腐蚀性气体和液体的钢铁件﹐常用厚约 3毫米的橡胶(如氯丁橡胶)或塑料(如氯化亚乙烯共聚物)黏在表面﹐可长期保护基体不受腐蚀。这种覆层主要用在大型抗蚀容器或排气系统中。埋在土壤中的金属构件﹐常以聚乙烯带包裹保护。在喷鉬或喷不锈钢的表面上涂覆聚四氟乙烯﹐在150℃温度下摩擦係数很低﹐磨损轻微﹐适於製造低载荷和要求高度清洁的滑动轴承﹐或用在食品﹑精细包装和纺织机械上。各国的Du﹑Dx轴承都是以塑料与金属复合製成的。通过静电喷涂将环氧树脂﹑氯化聚醚﹑聚四氟乙烯以及聚氯乙烯等塑料粉末涂覆在金属表面﹐可获多种抗化学腐蚀性极好的覆层﹐可用於输水﹑污水处理和海洋平台的设备上。有机覆层在辉光放电情况下﹐有机单体可以聚合成无针孔的有机膜﹐用作电容器的介质层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条