1) accelerate cooling system
快速冷却系统
1.
In order to improve product quality and rolling efficiency, a new set of accelerate cooling system of plates after rolling was designed for the plate rolling mill of Wuhan Iron and Steel Corporation.
针对轧板厂原有冷却系统冷却能力弱的实际情况,为了提高产品质量和生产效率, 专门为轧板厂生产线设计了一套全新的轧后快速冷却系统。
2) quick cooling system
快速冷却制冷系统
1.
Three types of designs of quick cooling systems for fresh milk in dairy cattle farms were given in this paper and their advantages and disadvantages were discussed,they were successfully used in the production of fresh milk in dairy cattle farms.
根据奶牛场鲜乳生产的特点和鲜乳保鲜的要求 ,对具有自动化挤奶设备的奶牛场鲜乳生产过程中鲜乳冷却保鲜所用的快速冷却制冷系统给出了几个设计方案 ,并分析了它们各自的优缺点 。
3) fast cylinder cooling system
汽缸快速冷却系统
4) fast cooling
快速冷却
1.
Fast cooling and ultra fast cooling experiments have been carried out on a Nb micro-alloyed steels.
通过对含Nb微合金钢控制轧制后,进行快速冷却+超快速冷却工艺的研究,得到了针状铁素体、板条马氏体及下贝氏体多相组织。
2.
It showed that a fast cooling after drawing was of benefit to dimensional stability, straightness, environmental stress cracking resistance, and strength of the drawn tubes.
数据说明拉伸后的快速冷却有利于管的尺寸稳定和直线度改善。
3.
When leakage occurs in the high pressure heater and the power unit is forced to shutdown for repair,fast cooling should be carried out by controlling outlet water from the dearator tank utilized with the level difference between the deaerator tank and the HP heater.
当高压加热器发生泄漏,机组被迫停运行进行故障抢修时,在原有热力系统设备的基础上,利用除氧器热水箱与高加标高的高度差,通过控制除氧器热水箱出水温度对高压加热器进行快速冷却。
5) rapid cooling
快速冷却
1.
Influence of rapid cooling and diffusion annealing on Sn-Bi-X solder;
快速冷却和扩散退火对Sn-Bi-X焊料的影响
2.
The experiments have been carried out to carefully investigate precipitation of cemenhte from pure iron during rapid cooling.
结果表明：快速冷却不能完全抑制三次渗碳体的析出，且三次渗碳体的拆出形貌（颗粒状、条片状）取决于钢的含碳
3.
in this paper,large section bearing steel bars are carried out the rapid cooling in the water coolers of turbulent tubes.
本文在现场湍流管式水冷器上对大断面轴承钢棒材进行快速冷却的基础上，研究了控冷后轴承钢的组织状态。
6) accelerating cooling
快速冷却
1.
The characteristics of the precipitates in microstructures during accelerating cooling and continuous hot rolling process were analyzed,and the size,distribution and quantities of the particles such as TiS and Ti_4C_2S_2 etc.
利用透射电镜分析了铸坯连续快速冷却及热连轧过程Ti-IF钢中第二相粒子的析出行为特征,将TiS,Ti4C2S2等析出粒子的尺寸、分布及数量分别与传统工艺的析出物进行了分析比较。
2.
The testing of producing 10～18mm gauges plate with recrystallization controlled rolling and accelerating cooling technology was simply introduced.
介绍了利用再结晶型控轧及快速冷却工艺 (RCR +ACC)生产厚 10～ 18mmQ34 5B中厚板的试验研究概况。
补充资料：敞开式循环冷却水处理系统
分子式：
CAS号：
性质：指吸收热量后的冷却水，通过冷却塔或蒸发池与大气直接接触进行蒸发冷却，然后再循环使用的一种处理系统。该系统除需经常补充新水，以平衡由于蒸发、风吹和排污过程损失的水量外，还须补加一定量的药剂，以保证循环冷却水的水质稳定。
CAS号：
性质：指吸收热量后的冷却水，通过冷却塔或蒸发池与大气直接接触进行蒸发冷却，然后再循环使用的一种处理系统。该系统除需经常补充新水，以平衡由于蒸发、风吹和排污过程损失的水量外，还须补加一定量的药剂，以保证循环冷却水的水质稳定。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条