1) 1Cr13 Type Martensite Stainless Steel
1Cr13型马氏体不锈钢
2) 1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
3) Cr13 stainless steel
1Cr13不锈钢
1.
Corrosion test methods, such as bacterial analyses, weight loss, electrochemical impedance spectroscopy, scanning electron microscopy (SEM) and EDXA, were used to study the effects of sulfate reducing bacterial (SRB) on corrosion of 1Cr13 stainless steel in sea mud and the corrosion of the steel in the macrocell composed of sea muds with and without SRB.
利用交流阻抗测试技术 ,扫描电镜及表面能谱、失重法、微生物分析等方法 ,在室内模拟条件下研究了海泥中硫酸盐还原菌对 1Cr13不锈钢腐蚀的影响 ,及在含和不含硫酸盐还原菌的海泥构成的宏电池腐蚀中 1Cr13不锈钢的腐蚀行为。
2.
The corrosion behavior of 1Cr13 stainless steel in soils were studied.
通过在酸性、中性及碱性土壤中埋设试件的方法,研究了1Cr13不锈钢分别经过1年、3年、5年这三种试验周期后的腐蚀行为特征。
4) martensite high-temperature
马氏体耐热型不锈钢
5) nitrogen bearing martensite stainless steel
含氮型马氏体不锈钢
1.
420U6 is a type of nitrogen bearing martensite stainless steel, it has increased(700~1 200)×10-6 nitrogen on the basis of SUS420J1, hence it has higher hardness and corrosion-resistting property.
420U6是一种含氮型马氏体不锈钢,在SUS420J1的基础上增加(700～1200)×10-6的氮,进一步提高了材料硬度和耐点蚀性能。
6) martensite stainless steel
马氏体不锈钢
1.
Anti-Bacteria Properties of High Copper Martensite Stainless Steel;
高铜马氏体不锈钢的抗菌性能
2.
In this paper, influence of remnant field intensity resulted from grinding process on friction coefficient of martensite stainless steel in the condition of short-time dry friction was investigated.
本文研究了马氏体不锈钢磨削加工产生的剩余磁场对其短时干摩擦过程中摩擦系数的影响。
3.
The reasons of center porosity,shrinkage cavities and surface quality in CC bloom of Martensite stainless steel have been analyzed and the effect of Mould-Electromagnetic Stirring and other factors on center porosity,shrinkage cavities and surface quality has been investigated.
对马氏体不锈钢方坯中心疏松、缩孔及表面凹陷的成因作了分析,探讨了电磁搅拌等对减少中心疏松、缩孔及表面凹陷的作用,并根据攀长钢公司的具体情况提出了预防措施。
补充资料：马氏体不锈钢
martensiticstainlesssteel：在空气或油中淬冷即得到马氏体组织的不锈钢。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条