1) re-injection system
回注系统
2) pouring system
浇注系统
1.
Study of the calculating formulas in the minimum section of the gray casting iron pouring system
灰铸铁件浇注系统最小截面积计算公式研究
2.
The injection molding flow of six different pouring system for air-condition panel was analyzed respectively by using Molding Plastics Advisers (MPA)software.
利用模流分析软件Moldflow Plastics Advisers(MPA)对空调机面板注塑模6种构型不同的浇注系统分别进行注射成型流动分析。
3.
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点,介绍了压铸模的浇注系统及模具结构设计。
3) gating system
浇注系统
1.
Simulation and optimization of gating system of die-casting die for magnesium alloy AM60B part;
AM60B镁合金压铸模浇注系统的模拟与优化
2.
Principle of Designing Gating System for Die Cast Aluminum Alloy Mould;
设计铝合金压铸模具浇注系统类型的原则
3.
Optimization of Gating System for Gear Box of the Car Based on CAE System;
基于CAE分析的汽车齿轮室浇注系统的优化
4) water injection system
注水系统
1.
Study on anti-corrosion and anti-scaling technology of water injection system in Qianda oilfield;
前大油田注水系统防腐防垢技术的研究
2.
A hydroviscous speed-regulating clutch used in oilfield water injection system;
油田注水系统用液体粘性调速离合器
3.
Energy-saving technology by adjusting input voltage of electromotor in water injection system.;
注水系统电动机调端电压节能技术试验研究
5) injection-production system
注采系统
1.
Corrosion and scaling prevention in injection-production system in Jilin oilfield;
吉林油田注采系统腐蚀、结垢防治技术
2.
Research on adaptability evaluation and adjustment mode of injection-production system of Lasaxing Oilfield;
喇萨杏油田注采系统适应性评价及调整方式研究
3.
However Pubei oilfield hasn’t developed injection-production system regulation in high water cut stage, so it is necessary to develop the research of injection-production system regulation method.
而葡北油田进入中高含水期的注采系统调整还没有开展过,因此,很有必要开展注采系统调整方法研究,通过开辟试验区以求找到最适应现开采条件下的调整方法,最大限度的提高水驱控制程度,增加原油可采储量,为油田可持续发展奠定物质基础。
6) runner system
浇注系统
1.
Design of runner system of injection mould for cellphone glass block;
手机镜片注射模浇注系统设计
2.
Manmade balanced design and numerical simulation for unbalanced runner system;
非平衡浇注系统的人工平衡设计与数值仿真
3.
Optimization of front bumper runner system and its implementation
汽车前保险杠浇注系统优化及实施
补充资料：回注
1.水流回旋灌注。 2.回头注视。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条