1) MPS process
小球烧结
1.
The paper presents the technical indices, process characteristics and application of MPS process at the NO .
本文介绍了包钢二烧车间９０ｍ２机上冷却烧结机技术指标、工艺流程特点以及小球烧结技术应用情况，同时扼要地讲述了改造内容、主体设备。
2) pellet sintering
小球烧结
1.
The technologies for new pellet sintering is introduced, by which solid fuel consumption can significantly be decreased, sinter quality can be improved, the utilization coefficient of sinter machine can be increased.
介绍了新型小球烧结法的一些新技术,采用这些技术可以大幅度降低烧结固体燃耗,改善烧结矿质量,提高烧结机利用系数。
3) small pellet sintering
小球烧结
1.
The process to realize small pellet sintering with techniques, such as thick ore layer sintering, low-temperature sintering, homogeneous-temperature sintering and high-oxidization-air sintering, with the new-built 180 m2 sintering machine in Xing Steel is introduced.
介绍了邢钢新建的180m2烧结机利用厚料层烧结、低温烧结、匀温烧结和高氧化性气氛烧结等技术实现小球烧结过程,转鼓强度提高了10。
4) MPS process
小球团烧结
1.
Point at the problems presented in MPS process, the uniform sintering technology was applied to perfect the MPS process in SHUIYE I & S Co As a result, the quality and quantity of sinter were increased and the fuel consumption was decrease
针对安钢集团水冶钢铁有限公司小球团烧结生产中存在的问题 ,采用均质烧结技术对其进行完善 ,取得了产质量提高 ,燃耗降低的良好效
2.
The output increased and coke saving of blast furnace was achieved by using MPS process.
三钢烧结厂在原烧结混合料准备系统上增加8个造球盘及配套设施,形成了小球团烧结生产的新工艺。
3.
The technical modifications with MPS process and many patents were presented in this paper As a result,the granulation ratio of mix was increased greatly ,the bed depth was increaed from 300mm to 550～ 600?mm and the solid fuel consumption was decreased obviousl
介绍了济钢烧结在技改过程中 ,采用小球团烧结技术及多项专利的情况。
5) MPS
小球团烧结
1.
A study on the fuel addition in MPS process;
小球团烧结燃料添加方式
2.
MEASUREMENT OF THE CONTENT OF RESIDUAL CARBON IN MPS;
小球团烧结矿残碳量的测定
3.
EXPERIMENTS FOR MPS PROCESS PARAMETERS DETERMINATION OF №2 SINTERING PLANT IN ANGANG;
鞍钢二烧车间小球团烧结工艺参数试验研究
6) MPS process
小球团烧结法
1.
, It is established that suitable size distribution of balling feed, higher ignition suction,lower sinter suction, higher bed depth and lower carbon rate are key factors to MPS process.
试验表明，小球团烧结法合理的工艺条件为：合理粒度组成的烧结料，较高的点火负压，较低的烧结负压，高料层，低配煤。
2.
In this paper, the commercial operation of MPS process in ironmaking plant,Anyang I & S Co.
本文介绍了安阳钢铁集团有限责任公司水冶炼铁厂小球团烧结法的工业生产实践和取得的先进指标。
补充资料：130m~(2)酸性小球带式烧结机(酒钢)
130m~(2)酸性小球带式烧结机(酒钢)
130m。酸性小球带式烧结机(酒钢)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条