1) mass ablative rate
质量烧蚀率
1.
Effect of laser parameters on mass ablative rate of carbon fiber reinforced composite;
激光参数对碳纤维复合材料质量烧蚀率的影响
2.
The results indicate that the composite ablative mass is directly proportional to the laser radiation energy when the laser radiation intensity is greater than 10 kW/cm2;with the same laser energy radiation,the mass ablative rate at high intensity of 0.
65 mm的激光辐照引起的复合材料的质量烧蚀率比半径为5。
2) erosion mass
烧蚀质量
1.
The internal temperature field of the insulation was calculated by using one-dimension two-layer model, and the conservation equations of energy and mass of the insulation surface were created, the pyrolysis gas mass and the erosion mass of the insulation at various time in the post-thrust phase were found.
首先用一维两层模型计算绝热层内部温度场,建立了绝热层表面能量和质量守恒方程,得到后效段绝热层各时刻的热解气体质量和烧蚀质量,再采用经典流体力学理论对后效段发动机内弹道进行了一维计算,而后计算发动机的后效推力。
3) ablation mass difference
烧蚀质量差
4) Thermal ablation rate
热烧蚀率
5) ablation rate
烧蚀率
1.
Unsaturated polyester(UP) inhibitor has many advantages and has been widely used in many rocket motors and gas generators,but it also has the disadvantage of high ablation rate.
通过功能填料选择试验,探索出基体材料中加入阻燃剂和耐烧蚀纤维的技术,研究了阻燃剂和耐烧蚀纤维加入量及耐烧蚀纤维长度对烧蚀率的影响。
2.
The results of line ablation rate,scanning electron microscope and thermal analysis showed that the type of polyorganosiloxane affected the ablative properties of silicone rubber most;the ablative properties of phenyl silicone rubber was superior to that of vinyl silicone rubber.
线烧蚀率、扫描电镜及热分析结果表明 :聚有机硅氧烷生胶的种类对硅橡胶烧蚀性能的影响最大 ,苯基硅橡胶的烧蚀性能优于乙烯基硅橡胶的烧蚀性能 ,生胶的残炭率是影响硅橡胶的烧蚀性能的主要原因 ;芳纶纤维和羟基硅油的用量对硅橡胶的烧蚀性能影响较大 ;气相法白炭黑的用量对硅橡胶烧蚀性能的影响最小 ,纤维和填料的分散状态对硅橡胶的烧蚀性能也有一定影响。
3.
The effect of varying the content of PSA pulp in the silicone rubber on its dispersion was analyzed,as well as the effect on the tensile strength,elongation at break,ablation rate and hardness of the resulting composite.
研究了PSA浆粕纤维含量对硅橡胶绝热材料的分散效果、抗拉强度、断裂伸长率、线烧蚀率、密度和硬度等性能的影响。
6) ablation rate
烧蚀速率
1.
Some calculations and analysis for three examples under different ablation rates were demonstrated.
针对金属表面的烧蚀过程,采用一维传热模型,将物体内的传热、温度变化分为2个阶段,即物体被加热到熔点温度的阶段及物体开始烧蚀阶段,使用积分近似的分析方法,完整地建立了表面烧蚀速率与表面加热功率之间的近似计算关系式。
2.
The effects of the respective content of silica aerogel and boron-phenolic resin on the properties of EPDM/NBR flexible insulation material,such as tensile strength,elongation-to-break,mass ablation rate,linear ablation rate and relative density were analyzed and compared.
通过比较分析白炭黑与硼酚醛树脂用量对EPDM/NBR柔性绝热层材料拉伸强度、断裂伸长率、质量烧蚀速率和线烧蚀速率以及相对密度的影响,得出随着白炭黑或硼酚醛树脂用量的增加,柔性绝热层材料的拉伸强度和相对密度呈递增趋势,烧蚀速率呈递减趋势,断裂伸长率在白炭黑和FB用量各自为20份时有极大值。
补充资料：弹头烧蚀(见弹头防热)
弹头烧蚀(见弹头防热)
warhead ablation
dantou shaoshi弹头烧蚀(warhead的lation)见弹头防热。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条