1) EP additive
极压剂
1.
By takeing deeply refined component oils of moderately viscosity as base oil,studing EP additives 、 oiliness additives used for L-MHEC22,reasonable formulation of the cutting oil was determined.
选用一定粘度的深度精制组分油为基础油,通过对L-MHEC22号切削油所用极压剂、油性剂的研究,确定了切削油的合理配方。
2.
The transparent MAF-1~# micro emulsible cutting fluid is developed by taking the lubricant with low viscosity and water as the basic materials, with the addition of the antirust agent, EP additive,foam inhibiting agent and surfactant.
以低粘度润滑剂和自来水为基本原料,添加以防锈剂、极压剂、消泡剂、表面活性剂,研制成透明的MAF-1#微乳型水基切削液,采用两相混合法的制备工艺。
3.
The test results of evaluation and application of sulfosalt EP additive are showed,at the same time its action mechanism is described aslo.
文中给出磺酸盐极压剂评定及应用试验结果 ,对该剂作用机理作了简介。
2) extreme pressure agent
极压剂
1.
The paper introduced the preparation of a new water soluble extreme pressure agent applied in processing of metals.
介绍了新型金属加工用的水溶性极压添加剂的研制 ,以含硫、磷、硼的单系极压剂 ,经TL型稳定调节剂复合成三元极压添加剂 ,具有水溶性、极压性、润滑性、防锈性、稳定性兼顾的特点。
2.
If all the hydrophilic group, adsorbable group, hydrophobic group and reactive group are in the some molecule this additive may also have the properties of oilness agent, antiwear agent and extreme pressure agent.
疏水性和反应性基团,则可能兼有油性剂、抗磨剂和极压剂多种作用。
3.
Under the condition of different temperature and friction pairs materials, the friction reducing properties of extreme pressure agents which contained phosphorus, sulphur, chlorine have been tested with pin plate wear instrument, the mechanism of friction reducing has been analyzed.
在销盘式摩擦实验仪上对几种含氯、硫、磷及硫磷复合的极压添加剂在不同温度与摩擦副材质条件下的减摩性能进行了测定，并讨论了减摩机理，查明了极压剂在不同温度与摩擦副材质条件下的减摩规律，为不同摩擦条件下极压剂的选择提供了依
3) extreme pressure
极压剂
1.
Discussion on sulfochlorcide isobotenyl uhich is midst of continuous production extreme pressuree sulphide isobutyi;
连续化生产极压剂硫化异丁烯中间体硫氯化异丁烯的工艺
2.
The water cutting fluid (adding the extreme pressure agent into water) was developed enormously because of the higher traveling heat factor and lower value.
根据国内外的实验研究 ,切削油中加入极压剂 ,切削表面的摩擦下降 6 0 %～ 80 %;加氢基础油黏度低、闪点高、蒸发损失少 ,为油基切削液低粘化创造了必要条件。
4) EP agent
极压剂
1.
The lubrication performances of six kinds of oiliness & EP agents were evaluated by five parameters determined by fourball tester.
用四球机试验的５个指标考察了６种油性极压剂的润滑性能，提出了添加剂种类与四球试验结果之间的关系。
6) oiliness & EP agent
油性极压剂
1.
The lubricity of oiliness & EP agent in oil is different from that in emulsion.
油性极压剂在油基和水基润滑剂中的润滑性能有较大差异,试验考察油性剂、极压剂对乳化液润滑性的影响,说明在乳化液中油性剂的极性是决定乳化液润滑性好坏的关键,而极压剂的浓度是决定乳化液润滑性好坏的关键,复合使用油性剂或油性剂与极压剂复合,润滑效果优于单剂。
补充资料：极压润滑剂极压润滑
分子式：
CAS号：
性质： 具有防止滑动面破坏的各种润滑剂称为极压润滑剂。极压润滑剂一般都含有极压添加剂。极压齿轮油、极压润滑脂、切削油、轧钢油等都含有极压润滑剂。这种润滑剂用于处在重载(或高接触应力)、高速、高温下滑动摩擦表面的润滑称为极压润滑。极压润滑通常是通过极压添加剂与金属表面生成极压膜将两摩擦表面隔开，以降低摩擦系数、减缓磨损，达到润滑的目的。
CAS号：
性质： 具有防止滑动面破坏的各种润滑剂称为极压润滑剂。极压润滑剂一般都含有极压添加剂。极压齿轮油、极压润滑脂、切削油、轧钢油等都含有极压润滑剂。这种润滑剂用于处在重载(或高接触应力)、高速、高温下滑动摩擦表面的润滑称为极压润滑。极压润滑通常是通过极压添加剂与金属表面生成极压膜将两摩擦表面隔开，以降低摩擦系数、减缓磨损，达到润滑的目的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条