1) post-batch-annealing
后罩式退火
1.
With the aim of producing deep drawing hot dip galvanized sheet of low carbon Al-killed steel on general production line for CQ(commercial drawing) and DQ(deep-drawing) products,the pre-batch-annealing process and post-batch-annealing process were tested on production line.
以在普通热镀锌线生产低碳铝镇静钢深冲热镀锌板为目标,根据CQ、DQ级热镀锌板生产线的工艺特点,设计了以前罩式退火和后罩式退火生产深冲热镀锌板的工艺方案,分别研究了2种工艺对低碳铝镇静钢热镀锌板性能的影响。
2) batch annealing
罩式退火
1.
Imitation Test of Batch Annealing and Continuous Annealing Recrystallizing of Interstitial Free Steel;
IF钢罩式退火与连续退火再结晶模拟试验
2.
This paper describes the application of PLC in HPH batch annealing system.
概述了HPH罩式退火炉应用情况,介绍了全氢罩式炉的生产工艺过程及其控制系统功能、特点,同时对LO I公司的HPH罩式炉控制系统在实际中出现的问题进行了阐述,并介绍了其改进方法及改造后的控制系统和效果。
3.
The structure and texture of continuous or batch annealing deep drawing and extra-deep drawing steel sheets were observed and analyzed.
对连续退火或罩式退火后的深冲钢板和超深冲钢板的组织以及织构进行了观测和分析。
3) pre-batch-annealing
前罩式退火
1.
With the aim of producing deep drawing hot dip galvanized sheet of low carbon Al-killed steel on general production line for CQ(commercial drawing) and DQ(deep-drawing) products,the pre-batch-annealing process and post-batch-annealing process were tested on production line.
以在普通热镀锌线生产低碳铝镇静钢深冲热镀锌板为目标,根据CQ、DQ级热镀锌板生产线的工艺特点,设计了以前罩式退火和后罩式退火生产深冲热镀锌板的工艺方案,分别研究了2种工艺对低碳铝镇静钢热镀锌板性能的影响。
4) batch annealing
罩式炉退火
1.
This paper is to solve the problems of complex process, numerous constrains and difficulty in modeling in the bell-type batch annealing shop.
针对罩式炉退火过程工艺复杂、约束多、难于解析建模的问题,首先分析了退火工艺流程,并进行了问题抽象,然后利用离散事件仿真技术和面向对象建模技术建立了罩式炉退火车间的仿真模型。
5) hood-type annealing furnace
罩式退火炉
1.
Coil suspension stacking technology for hood-type annealing furnace;
罩式退火炉钢卷悬浮式堆垛技术改造
2.
According to structure characteristics and technological requirements of hood-type annealing furnace,Simatic S7-300 PLC is used as a kernel control unit of the system.
针对罩式退火炉结构特点及退火工艺要求,以西门子S7-300 PLC为核心控制设备,采用Profibus总线实现整个系统的主从站分布式I/O控制,利用西门子Step7软件实现控温系统的PID限幅控制和脉冲燃烧控制。
6) bell-type annealing furnace
罩式退火炉
1.
Heat transfer efficiency of inner covers with different shapes in a bell-type annealing furnace;
罩式退火炉不同内罩结构传热效率
2.
The bell-type annealing furnace is used for the periodic annealing of various materials.
罩式退火炉用于多种材料的周期式退火。
补充资料：软化退火(见低温退火)
软化退火(见低温退火)
soft-annealing
rU0nhUO tUihUO软化退火(soft一annealing)见低温退火。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条