1) roll collar
辊环
1.
The effect of different amounts of K/Na-RE addition into high-speed steel(HSS) used for roll collar was investigated utilizing Hi-scope video microscope(HSVM) and mechanical property measurement.
在辊环用高速钢中添加不同含量的K/Na-RE复合变质剂,对试样分别进行HSVM及力学性能测试。
2.
A kind of high speed steel roll collar with high wear-resistance has been developed usingcentrifugal casting technique, to replace common alloy cast iron rolf collar with low wear-resistance and hard alloyroll collar with high price.
常用合金铸铁辊环耐磨性低,而硬质合金辊环成本高,采用离心铸造方法,开发了耐磨性能优良的高速钢辊环,高速钢辊环的硬度达63～65HRC,辊面硬度差小于2HRC,冲击韧性大于16J/cm~2。
3.
We research the effect of high speed steel compositions, centrifuge casting technology parameter and composite modification on the properties of high speed steel roll collar.
研究了高速钢成分、离心铸造工艺参数和复合变质处理对高速钢辊环性能的影响。
2) roll ring
辊环
1.
The application of high speed steel roll ring in the High Speed Wire Rods Plant of Tiangang Group is introduced.
介绍了高速钢辊环在天钢高线厂应用的情况,对高速钢辊环与碳化钨辊环的优缺点进行了对比,提出了高速钢材质辊环、轧辊在轧钢厂使用的可能性。
2.
The assembly designs of roll ring suffice not only for the lower limit of rolling moment,but also for the upper limit of roll ring strength.
辊环装配设计既要满足轧制力矩传动的下限条件,又受到辊环强度的上限条件限制,设计计算要求较高精度。
3.
The pressure value on the taper sleeve during fixing roll ring of cantilevered mill for high speed wire rod was calculated by analyzing the balance of force and moment of the taper sleeve So,the problems of roll collapse and loose can be avoided,which caused by large and small pressure on the taper sleev
通过对高线悬臂式轧机辊环安装固定中锥形套的受力分析 ,计算了加压工具的加压值 ,从而避免了加压过大造成崩辊 ,加压过小造成松辊的问
3) roller ring
辊环
1.
Development of CSP furnace roller ring;
CSP加热炉炉辊辊环的研制
2.
The WC_p/steel composites roller ring was formed by centrifugal casting,and the microstructure and properties of this composite material were analyzed.
用离心铸造工艺制备了WCp/钢基复合材料辊环,并对所制备的复合材料进行了分析与性能测试。
3.
The mechanical properties, microstructures and application of centrifugal casting composites roller ring have been investigated by SEM EDS-analysis in the paper .
通过扫描电镜、电子能谱分析,研究了离心铸造复合材料辊环的机械性能,微观组织及其应用。
4) ring
[英][rɪŋ] [美][rɪŋ]
辊环
1.
Stress analysis of roll ring in H beam mill;
万能轧机热装镶套水平轧辊辊环应力分析
2.
State the basic principles of grade arrangement of carbide rings comprehensively on differnet finishing stands under various environmnet and stage.
阐明了硬质合金辊环在不同生产条件下，在精轧机不同机架上牌号配置的基本原则。
3.
In the paper, The stress of the roll ring in the unversal mill is analyzed.
本文对H型钢轧机水平辊辊环的各种应力分析比较得出,对万能轧机镶套水平轧辊辊环作用最大的应力为热装应力,提高辊环与辊芯之间的摩擦系数,减少热装过盈量是改善辊环受力状态的有效途径。
6) composite roll ring
复合辊环
1.
In order to make tungsten carbide/steel composite roll rings of low cost,based on the relationship between required bonding strength and rolling torque and the bonding strength of different glues,the tungsten carbide/steel composite roll rings were developed by use of chemical bonding,and the composite rolls were tested on the Pomini mill.
为了制造低成本的硬质合金/钢复合辊环,根据对复合强度与轧制扭矩关系的计算及对不同胶结剂复合强度研究,用化学胶结工艺制造了硬质合金复合辊环,与辊轴装配成复合轧辊,在Pomini棒材轧机上进行了轧制性能试验,与冶金工艺制造的复合辊环进行了对比。
补充资料：辊辊
1.犹混混。形容苟且混世。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条