1) warm rolling
温轧
1.
By warm rolling after hot rolling or cold rolling after annealing in process and stabilizing annealing in some temperature condition,the c.
采用热轧后温轧或中间退火后冷轧,再在一定温度下进行稳定化退火的工艺,可以获得综合性能良好的铝-镁-钪合金冷轧板材。
2.
The effects of deformation degree of warm rolling with two rollers and cold rolling with multi rollers, the matching relation of deformation between diameter and wall thickness, the temperature of warm rolling, annealing temperature of semi-product and finished product and chemical composition on shaping quality, microstructure and properties of TC2 tube were studied.
对TC2钛合金管材研制中的两辊温轧、多辊冷轧变形程度及直径壁厚变形匹配关系、温轧加热温度、中间及成品退火温度、化学成分等对管材加工成形质量、组织性能等的影响进行了研究。
3.
0mm hot strip of low carbon steel produced by Flexible Thin Slab Rolling with warm rolling technology were investigated using optical microscopy, scanning electron microscopy, transmission electron microscopy, electron back scattered diffraction.
本文利用光学显微镜、SEM、TEM及EBSD技术研究了FTSR生产线采用温轧工艺生产的3。
2) temperature and rolling control
控温控轧
3) finishing rolling temperature
终轧温度
1.
The effect of finishing rolling temperature on banded structure of 16Mn steel plate;
终轧温度对16Mn钢板带状组织的影响
2.
Influence of finishing rolling temperature on microstructure and properties of Q450NQR1 high strength weathering steel
终轧温度对高强度耐候钢Q450NQR1组织和性能的影响
3.
By using controlled rolling and cooling,optical and electron microscopy observation,mechanical test etc,the microstructure of hot-rolled 60Si2CrVAT rolled with different finishing rolling temperature,and the effect of hot rolled structure on the microstructure and properties of heat treated products were studied.
以铁路用弹簧钢60Si2CrVAT为研究对象,通过工业控轧控冷试验,采用光学、电子显微技术和力学分析等方法,系统研究了在不同终轧温度下热轧态的组织结构以及对其热处理后组织性能的影响。
4) isothermal-rolling
恒温轧制
1.
The outline of superplastic and anisotropic behavior in AZ91D grain refined by isothermal-rolling is summarized comprehensively.
本文综合评述了日本目前对恒温轧制微细化AZ91D板材的超塑性及其各向异性的研究情况。
5) low temperature rolling
低温轧制
1.
Production practice of low temperature rolling of 45 steel;
45钢低温轧制的生产实践
2.
In order to reduce production cost, the best production process using niobium microalloy instead of vanadium to produce Q345B plates of different thickness is discussed through analyzing the reason of forming Widmannstaetten structure and the influences of slab thickness, the reduction in pass, low temperature rolling and control cooling etc on the grain size and the properties.
为降低生产成本,通过分析钢板形成魏氏组织的原因以及中间坯厚度、道次变形量、低温轧制和控制冷却等对钢板组织晶粒度和性能的影响,探讨了采用铌微合金化代替钒生产不同厚度Q345B钢板的最佳生产工艺。
3.
This paper introduces the development of low temperature rolling technology for wire and rod.
介绍了国内外棒线材低温轧制技术的发展情况。
6) final rolling temperature
终轧温度
1.
The effects of final rolling temperature and cooling rate on microstructure at room temperature were studied.
通过Gleeble-1500热模拟机对20CrMo轧材精轧阶段轧制过程及冷却过程的模拟,研究了终轧温度、冷却速度对室温组织的影响,分析了形成带状组织的条件,最终得出了理想室温组织的终轧温度和冷却速度。
2.
Influence of final rolling temperature, cooling rate and tempering on properties of fire-resistant steel was researched.
测定了耐火钢的CCT曲线,研究了耐火钢的性能,包括室温和高温拉伸性能、系列温度下的冲击性能、应变时效性能等;探讨了终轧温度、冷却速度、回火对耐火钢性能的影响。
3.
According to the characteristics of micro-carbon steel,simulative test was taken in laboratory under the principle of "high heating temperature,high beginning rolling temperature,high final rolling temperature and low rolling temperature".
针对微碳钢的特点 ,在实验室进行了模拟试验 ,在“三高一低”的原则下 ,研究了微碳钢加热温度对AlN溶解的影响 ,终轧温度及冷却速度对热轧晶粒度的影响 ,卷取温度对AlN和渗碳体析出的影响。
补充资料：温轧
温轧
warm rolling
WenZhQ沮轧(warm rolling)在金属或合金常温组织发生回复的温度以上，再结晶的温度以下的温度范围内进行的乳制过程。由于温轧时材料的加工硬化得到一定的回复，与冷轧相比，材料的屈服强度低，塑性高，又没有热轧的缺点，因此受到普遍重视。温轧一般在冷轧设备上进行。在进入轧制变形区之前用感应加热器将工件加热到200一400‘C，然后进行轧制。一些塑性低、强度高的金属通过温轧也有可能得到精加工。温轧的延伸率约为冷轧的2一3倍。 温轧适用于加工一些在常温条件下塑性低、屈服强度高、变形抗力大、不适合采用冷轧的金属和合金。也用来加工那些虽能冷轧，但生产效率低、轧程多、能耗大的金属和合金，如轧制铁铝合金、不锈钢板等。 (韦光)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条