1) eccentric shaft
偏心轴
1.
Forming process and dies of cold and warm extrusion for location eccentric shaft;
定位偏心轴冷温挤压成形工艺及模具
2.
Sand-belt grinding process applied to grinding the eccentric shaft of mining crusher
砂带磨削在破碎机偏心轴加工工艺上的应用
3.
Aiming at the design shortage of the vibration generator system in the quick-change dais for 4# continuous casting machine,the stub diameter of the eccentric shaft is increased from 75mm to 110mm,the transition corner radius in the root of the stub is increased from 1.
针对4#连铸机快速更换台振动发生装置原设计存在的不足,将偏心轴轴头直径由75mm加大为110mm,轴头根部过渡圆角半径由1。
2) Eccentric Axis
偏心轴
1.
Productivity and accuracy of Processing eccentric axis have a great relationship to the fixture.
加工偏心轴的生产效率和精度与夹具有密切的关系。
2.
The machining methods of the eccentric axis on NC lathe without gasket are researched.
探讨了在数控车床上不加垫片实现偏心轴零件加工的方法,建立了编制偏心轴零件数控车削加工程序的数学模型,利用FANUC 0i-TA系统用户宏程序功能编写了偏心轴零件的数控车削加工用户宏程序,并对数控车削加工偏心轴零件应注意的问题进行了说明。
3) Eccentric axle
偏心轴
1.
In this paper,the formula of combustion gas pressure which act to eccentric axle of rotary engine has been given in theory.
从理论上推导了转子发动机偏心轴瞬时气动力计算公式,应用有限元技术,计算了某转子发动机偏心轴的强度,从而为偏心轴设计和定型提供依据。
4) eccentric shafts
偏心轴
1.
Influencing factors of force difference in rolling zone of eccentric shafts during cross wedge rolling;
偏心轴类零件楔横轧轧制区轧制力差的影响因素
5) eccentricity axis sheath
偏心轴套
6) Eccentric hollow shaft
空偏心轴
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条