1) deposition pressure
沉积压力
1.
The effect of deposition pressure on the properties of PC film;
沉积压力对Parylene C膜性能的影响
2.
The structure and properties of the films during the course of deposition and polymerization were dominated by deposition pressure.
采用化学气相沉积法制备的聚氯代对二甲苯(PPXC)薄膜具有优异的耐溶剂腐蚀及气体阻隔性能,其沉积聚合过程中,沉积压力对膜的结构与性能具有显著影响。
3.
Effects of deposition pressure on structure and properties of thin film were investigated using XRD,SEM,UV-Vis spectrometer and FT-IR four-probe resistivity meter.
采用射频(RF)磁控溅射方法在玻璃衬底上制备了氢化纳米硅薄膜,研究了沉积压力(4~9 Pa)对薄膜结构和性能的影响。
2) deposition voltage
沉积电压
1.
Influence of deposition voltage on nanoporous ZnO films by electrochemical synthesis;
沉积电压对电化学合成纳米ZnO多孔薄膜的影响
2.
The influence of deposition voltage on the phase composition and microstructure of HAp coatings was investigated.
采用水热电沉积法在碳/碳复合材料表面制各了羟基磷灰石(hydroxyapatite,HAp)涂层,用X射线衍射、扫描电子显微镜,万能材料试验机等测试手段对涂层进行了表征,研究了沉积电压对HAp涂层晶相和显微结构的影响。
3.
The effect of deposition voltage on auxiliary heat PCVD-TiN coatings has been studied.
研究了不同的沉积电压对辅助加热式PCVD -TiN涂层的影响。
3) deposition pressure
沉积气压
1.
To lower the surface roughness of diamond thin films by improving the CVD depositing technology, two kinds of new technical methods are proposed by appropriately increasing the carbon source concentration and controlling the deposition pressure.
为通过改进CVD沉积工艺减小金刚石薄膜表面粗糙度 ,提出了适当提高碳源浓度和合理控制沉积气压两项新的工艺方法 ,并通过切削试验研究了其对金刚石薄膜刀具耐用度及切削性能的影
2.
For the diamond films prepared at high deposition pressure,scanning electron microscope images show clearly the crystals and the Raman spectra have sharp peaks at 1332 cm-1,which shows good quality of diamond films.
研究了微波化学气相沉积中沉积气压对金刚石薄膜生长速率和质量的影响。
3.
The influence of different substrate temperature and different deposition pressure on the crystallinity of GaN films are systematically studied by X-ray Diffraction(XRD),Atomic Force Microscope(AFM).
研究表明,在750℃的沉积温度时,GaN薄膜的结晶质量较高;在20 Pa以下的沉积气压下,GaN薄膜的晶体质量随着沉积气压的升高而提高。
4) gravitational deposition
重力沉积
1.
Unsupported macroporous ZrO_2 membranes were successfully synthesized by vacuum filtration or gravitational deposition as assembly methods using monodispersed PMMA as template.
以聚甲基丙烯酸甲酯(PMMA)为成孔模板剂,采用抽滤和重力沉积的组装方法制备了对称的大孔ZrO2膜。
5) sedimentary dynamics
沉积动力
1.
Silt movement of Lingdingyang Bay in Zhujiang Estuary and analysis of sedimentary dynamics;
珠江口伶仃洋泥沙运动的沉积动力作用
6) deposition pressure,deposition tension
沉积张力
补充资料：锅炉、压力容器、压力管道及特种设备定期检验
锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment
guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】，on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。，p~切reves-Sels，p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用，规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度，做好检验计划，按时向检验单位提出申请。检验单位应该保证及时进行检验，检验按有关检验规则进行。检验时，设备使用单位应做好配合工作，提供必要的运行资料。检验完毕，检验单位要出具检验报告，对设备能否使用，要作出明确结论。如设备有缺陷，要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告，发使用许可证书。有缺陷的，责令使用单位修理，修理后检验仍不符合安全要求的，则通知报废。使用单位逾期不进行定期检验，锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条