1) porous Cu
多孔铜
1.
It is shown that open- cell porous Cu can be fabricated by using commercially pure Cu powder and carbamide particles through consolidating,sintering and dissolving processes,the pore size and porosity of which can be varied in the ranges of 60%-80% and 100-400μm,respectively.
利用烧结-脱溶法制备出了多孔铜材料,并通过形貌观察和压缩试验对其孔结构和力学性能进行了表征。
2) porous copper
三维多孔铜
3) Porous
多孔
1.
Discuss of Warm Compaction for Manufacturing Porous Iron;
温压工艺制备多孔铁基金属的探讨
2.
Research on preparation and structure of porous B-doped polycrystalline diamond;
多孔含硼金刚石多晶体的制备与结构研究
3.
Synthesis of Antibacterial Ag-carrying SiO_2 Nano-porous Blocks with a Slow Release of Silverions;
缓释型载银抗菌SiO_2纳米多孔块材的合成
4) multi-hole
多孔
1.
Discussion on the single-strand process of multi-hole PET interlaced set yarn;
多孔涤纶低弹网络丝单股生产工艺探讨
2.
One kind of multi-hole aluminum anodization films was prepared by two-step aluminum anodization in the solution of oxalic acid, and then stripped from the aluminum substrate by reverse-current stripping technique.
采用二次铝阳极氧化法在草酸体系中制备多孔铝阳极氧化膜,用逆电剥离技术将氧化膜从铝基体上剥离。
5) Ultra-high porous silicon
高多孔度多孔硅
6) porous metal
多孔金属
1.
Electromagnetic wave absorption properties of aluminum foams-based porous metal composite;
泡沫铝基多孔金属复合材料吸波性能
2.
Preparation of Lotus-type Porous Metal with Metal-gas Eutectic Directional Solidification;
金属-气体共晶定向凝固制备藕状多孔金属的研究
3.
Structure design and material choice of porous metallic substrate supporter;
多孔金属基载体材料的选择与结构设计
参考词条
补充资料：多苯基多亚甲基多异氰酸酯
多苯基多亚甲基多异氰酸酯，简称PAPI，或称粗MDI，浅黄色至褐色粘稠液体．有刺激性气味。相对密度(20℃／20 ℃)1．2，燃点218℃。PAPI实际上是由50％MDI与50％官能度大于2以上的多异氰酸酯组成的混合物。升温时能发生自聚作用。溶于氯苯、邻二氯苯、甲苯等。PAPI的活性低，蒸气压低，只是TDI的百分之一，故毒性很低。
用于制造聚氨脂胶粘剂。也可直接加入橡胶胶粘剂中，改善橡胶与尼龙或聚酯线的粘接性能。贮存于阴凉、通风、干燥的库房内，远离火种、热源。严格防水、防潮，避免光照。
用于制造聚氨脂胶粘剂。也可直接加入橡胶胶粘剂中，改善橡胶与尼龙或聚酯线的粘接性能。贮存于阴凉、通风、干燥的库房内，远离火种、热源。严格防水、防潮，避免光照。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。