1) gas blowing
吹气
1.
Water modeling on gas blowing in tundish;
中间包吹气的水力学研究
2.
Simulation study of slab continuous casting tundish with bottom gas blowing;
板坯连铸中间包底吹气数值模拟研究
3.
Effect on steel liquid flow in the bottom gas blowing tundish of different porous materials was studied using water modeling.
采用不同性能参数的多孔透气砖进行中间包底部吹气水模实验,研究透气砖的气孔率、透气度、平均孔径对所形成的气泡大小和能形成有效气幕所需条件的影响,并分析使用不同透气砖时的RTD曲线,对使用不同透气砖时的吹气参数进行了优化。
2) blowing
[英]['bləuiŋ] [美]['bloɪŋ]
吹气
1.
Effects of jet blowing on the side force of forebodies with different cross section;
不同截面机身头部吹气方式对侧向力的影响
2.
Under the same reheating conditions, the influence of time sequence of stretch and blowing (characterized with delay time t0) on the preform growth in stretch blow molding (SBM) was studied using a transparent mold and a digital camcorder.
在型坯再加热条件不变的情况下,通过全透明模具和数码摄像机研究了两步法拉伸吹塑中拉伸与吹气的时序(即预吹气延迟时间t0)对型坯拉伸吹胀模式的影响。
3.
A flow visualization investigation on leading edge breakdown is conducted in a wind tunnel to identify the effect of blowing on a strake wing model undergoing large amplitude pitching motions.
实验采用翼面吹气控制翼面非定常流动，通过烟流显示涡轨迹和涡破碎位置，用相锁照相技术记录空间流态。
3) gas injection
吹气
1.
In this paper, the changing of flow in tundish during the process from ladle to tundish is simulated by k-ε modle with numerical simulations after the gas injection.
模拟结果表明:吹气前从长水口流出的钢水,呈向下流动的趋势,然后直接流向出口;吹气后中间包内钢液的流动方向发生改变,钢液并未向下流动,而是先上升到渣金交界面,然后沿渣金界面流向中包的出口,后一种流动有效地增加了钢液在中间包的停留时间,增加了夹杂物与渣的接触时间,有利于中间包钢水成分及温度的均匀,特别有利于夹杂物的去除。
4) blowing and sucking
吹气吸气
6) gas injection
喷吹煤气
1.
Slag formation in blast furnance with gas injection was studied by simulation experiment.
对喷吹煤气后高炉的成渣过程进行了模拟研究,结果表明:FeO的含量决定了初渣的性能。
补充资料：吹气管液位检出装置
分子式：
CAS号：
性质：检出装置吹气管插入被测容器中，以压缩空气作为能源，用恒压差继动器保持吹气流量恒定。当管口有一定的气泡逸出液面时，管内静压反映液位高度，静压由压力变送器转换成电或气的统一信号由显示仪表显示。可用于敞口容器中有腐蚀性、易结晶或沉淀等的介质液位检测。
CAS号：
性质：检出装置吹气管插入被测容器中，以压缩空气作为能源，用恒压差继动器保持吹气流量恒定。当管口有一定的气泡逸出液面时，管内静压反映液位高度，静压由压力变送器转换成电或气的统一信号由显示仪表显示。可用于敞口容器中有腐蚀性、易结晶或沉淀等的介质液位检测。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条