1) flash oil
飞溅油
1.
600 mm thickness of the wire net layer is adopted in the FFA scrubber on top of the homemade plate deodorizer to scrubber the flash oil and the FFA,so that the acid value of the distillate can be improved to 90 mgKOH/g,and the oil content in the distillate c.
国产板式脱臭塔通过改用600 mm厚丝网层捕集飞溅油和游离脂肪酸,可提高馏出物的酸值到90 mgKOH/g,同时可降低馏出物中的含油量,提高油脂精炼率0。
2) spatter
飞溅
1.
Mechanism and influencing factors of spatter formation with self-shielded flux cored wire;
自保护药芯焊丝飞溅的形成机理及其影响因素
2.
Effect of Activating Flux on Appearance of Welds and Spatter in CO_2 Arc Welding;
活性剂对CO_2气体保护焊焊缝成形及飞溅的影响
3.
Investigation of spatter for CO_2 gas-shielded welding;
CO_2气体保护焊飞溅问题的研究
3) splash
飞溅
1.
The results show that to use activation dosage can reduce welding splash rate greatly,increase weld fusion depth,widen fusion width,and increase depth and width ratio and fusion drops transition with thin particles.
结果表明,使用活性剂可以使焊接飞溅率大大降低,焊缝熔深增加,熔宽增大,深宽比增加,熔滴以细颗粒过渡。
2.
The abnormal currents are caused by splash.
飞溅将引起电流信号的异常变化。
3.
The effects of transfer shape about droplet, stress of droplet, gap between twin electrode, barrel form and motion manner of electrodes on splash factors of twin electrode single arc welding were studied by the high - speed photographs.
利用高速摄影等实验手段,研究了双电极焊条单弧焊熔滴过渡形态、熔滴受力、双芯间隙、焊条套筒形 式、双电极焊条焊接时运条方式等对飞溅的影响。
4) welding spatter
焊接飞溅
1.
Nowadays the researchon the application of GMAW puts great emphasis on the following aspects: Reducing welding spatter,increasing welding efficiency and deskillization of welding equipments.
目前GMAW工艺的研究着重于：抑制焊接飞溅，提高焊接效率，以及实现焊接设备的脱技能化。
2.
Each waveform controlling parameter expresses a different influence on the welding spatter.
在波形控制的CO2焊中控制参数较多,不同的控制参量对焊接飞溅表现出不同的影响规律。
5) splash zone
飞溅区
1.
The corrosion behavior of hot dip Galvanized(GI),Galfan(GF) and Galvalume(GL) coated steels exposed to splash zone of Qingdao site was investigated with seawater corrosion test and microscopy morphology analyses.
6%硅(GL)镀层钢板在青岛站的飞溅区海水腐蚀行为,并利用腐蚀质量损失测试和显微结构分析,研究3种镀层钢板的海水飞溅区腐蚀行为。
2.
Corrosion results of 12 types of copper alloys exposed to marine splash zone at Qingdao Sea area of China were reported.
研究了12种铜合金在青岛海域飞溅区暴露16年的腐蚀结果及其腐蚀行为和规律。
3.
Based on the using conditions of aluminium-steel joints,we exposed such samples in splash zone,ebb and flow zones in Qingdao,Zhoushan and Xiamen areas.
按照爆炸复合材料的应用条件,将铝-铝-钢投放在青岛、舟山和厦门3个海域的潮差和飞溅区,暴露1a后研究了材料的腐蚀和力学性能。
6) spatter
焊接飞溅
1.
Effects of flux compositions of self-shield hardfacing flux-cored wire such as rutile,fluoride, wollastonite,zircite and magnesia on spatter were studied by orthogonal experimental design,an optimal mixture ratio of varied flux powders for nitride alloyed self-shield hardfacing flux-cored wire was got.
用正交试验法探讨了自保护硬面药芯焊丝药芯粉中金红石、氟化物、硅灰石、氧化锆和镁砂对焊接飞溅的影响,对含氮自保护硬面药芯焊丝药芯粉的最佳配比进行了优化。
参考词条
补充资料：皂化溶解油、肥皂油和调水油
分子式：
CAS号：
性质：又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂（如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂）和少量稳定剂（如乙醇或甲醇）而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主，润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
CAS号：
性质：又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂（如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂）和少量稳定剂（如乙醇或甲醇）而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主，润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。