1) Gelation Time
凝胶化时间
1.
The gelation time of the given system was determined according to Cham- bon-Winter(CW)criterion.
根据Chambon-Winter(CW)法则确定了不同体系的凝胶化时间,探讨了溶胶-凝胶化转变过程中体系粘度的变化以及温度、添加剂对体系凝胶化时间的影响,为连续莫来石纤维干法纺丝工艺提供了一定的理论依据。
2.
The gelation time and the CH_2OH index measured by FT-IR spectrometer were employed respectively to investigate the reactivity of the synthesized expandable phenolic res.
建立了用凝胶化时间和FTIR分析的羟甲基指数来判断酚醛树脂活性的方法,并跟踪分析了树脂活性在反应过程中的变化。
3.
The less the gelation time of Al_2O_3 -Si.
用４ｍｏｌ／ＬＮＨ＿３·Ｈ＿２Ｏ催化的Ａｌ＿２Ｏ＿３－ＳｉＯ＿２溶胶的凝胶化时间越短，经高温热处理后莫来石晶须含量越高。
2) gel time
凝胶化时间
1.
The effect of the reaction time,reaction temperature,the component of the episulfide resin on gel time of novalac epoxy-episulfide resin was reasearched.
实验结果表明,随着环硫树脂的量的增加,凝胶化时间逐渐缩短。
2.
Dicyclopentadiene can be polymerized by RIM using a catalyst system based on WCl6/WOGl4-AlEt3 Ring-opening polymerization results in formation of a crosslinked polymer, The effects of the amount of catalyst and activatior,as well as the reaction temperature on gel time are studied.
本文研究了反应条件对凝胶化时间的影响。
3.
By determing the gel time of curing procedue and the IR absorption spectrum,the accelera-tive action of thiourea and its dereivates in curing of dicyandiamide/epoxide resin systems is studied.
通过测定固化过程的凝胶化时间及红外光谱图,考察了硫脲及其衍生物对二氰二胺/环氧树脂体系的固化促进作用;讨论了硫脲及其衍生物/二氰二胺/环氧树脂体系的组成配比对固化特性、室温贮存性能和固化后粘合剪切强度的影响。
3) gel-hardening time
胶凝硬化时间
1.
The results show that the gel-hardening time of the ceramic mold production was about 8 minutes, and a high wet strength of 0.
8、18%、10%的条件下,所生产的陶瓷铸型的胶凝硬化时间为8min左右,湿强度为0。
4) gel time
凝胶时间
1.
Quantity of accelerant affected to gel time of anchoring agent for resin bolt;
促进剂用量对树脂锚杆锚固剂凝胶时间的影响
2.
Factors influencing the gel time of DCPD-type unsaturated polyester resin for coatings;
影响涂料用DCPD型不饱和聚酯涂料凝胶时间的因素
3.
Influence of the temperature on the gel time of the capsules in rock bolting system;
温度对树脂锚杆锚固剂凝胶时间的影响
6) gelation time
胶凝时间
1.
The results showed that the gelation time decreased with the curing temperature increasing,and at the optimized curing temperature(160℃),the gelation time was 126s and the appa.
结果表明:钡酚醛树脂的胶凝时间随温度升高而缩短,在最佳固化温度(160℃)时的胶凝时间为126 s,固化反应的表观活化能为60。
2.
The effects to the gelation time of water, the temperature , the pH value, the concentration of crosslink have been studied.
研究了水质、交联剂浓度、pH值对凝肢体系胶凝时间的影响。
3.
The gelation time was used as a scale standard of stability of TiO.
以胶凝时间作为TiO2溶胶稳定性的衡量标准,研究了加水方式、Acac含量、加水量、溶剂量、HCl量、水解温度等对TiO2溶胶胶凝时间的影响,从中选取一种稳定的溶胶用于制膜研究。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条