1) Ignition-proof magnesium alloy
![点击朗读](/dictall/images/read.gif)
阻燃镁合金
1.
Ignition-proof mechanism of ignition-proof magnesium alloy with rare-earth addition is introduced here.
综述了稀土阻燃镁合金的阻燃机理及其研究的最新进展。
2.
The development direction of high- strength magnesium alloy,heat-resistance magnesium alloy and ignition-proof magnesium alloy are discussed.
论述了高强度镁合金、高温镁合金及阻燃镁合金的研究重点及发展方向。
3.
Experimental results for microstructure and mechanical properties of LFC ignition-proof magnesium alloy indicate that with the addition of RE, a new rod-like eutectic RE_3Al_(11) phase is formed.
对消失模铸造阻燃镁合金的组织和力学性能的试验研究表明 ,RE的加入在组织中出现了枝条状共晶Al1 1 RE3相 ,并未形成粗大 Al2 RE相 ,同时晶界上离异共晶 β相的数量大大减小 ,且呈不连续网状或孤立块状分布。
2) Ignition proof magnesium alloys
![点击朗读](/dictall/images/read.gif)
阻燃镁合金
1.
At present, the research and development about ignition proof magnesium alloys have received much attention all over the world, and consequently many researches have been carried out.
综述了阻燃镁合金的研究开发现状,尤其是Ca、Be、Zn和稀土在镁合金中的阻燃作用及其阻燃机理,指出了阻燃镁合金研究目前还存在的问题和今后的研究重点。
2.
The current situation of the research on the ignition proof magnesium alloys is reviewed.
![点击朗读](/dictall/images/read.gif)
介绍了镁合金的燃烧机制,总结了阻燃镁合金的研究现状,分析了合金元素Ca、Be、Zn和稀土的作用,指出其未来发展的方向。
4) aluminum magnesium composite flame retardant
![点击朗读](/dictall/images/read.gif)
铝镁复合阻燃剂
5) burn resistant titanium alloy
![点击朗读](/dictall/images/read.gif)
阻燃钛合金
1.
Ti40 alloy is a new type burn resistant titanium alloy developed by China.
![点击朗读](/dictall/images/read.gif)
阻燃钛合金具有重要的应用前景,Ti40合金是我国研制的新型阻燃钛合金。
6) burn-resistant titanium alloy
![点击朗读](/dictall/images/read.gif)
阻燃钛合金
1.
Two Ti-V-Cr system burn-resistant titanium alloys of Ti-25V-15Cr-0.
![点击朗读](/dictall/images/read.gif)
2Si2种阻燃钛合金,分别测试其在不同热暴露和蠕变工艺条件下的热稳定性能和蠕变性能,并观察了组织。
2.
Three kinds of Ti-V-Cr burn-resistant titanium alloys with different V contents have been prepared.
配制不同V含量的3种阻燃钛合金,分别测试其在不同热暴露和蠕变工艺下的热稳定性能和蠕变性能,并观察其显微组织。
3.
To avoid the shortages of body burn-resistant titanium alloy like lower ratio strength, poor work process property and expensive cost, Cu element was introduced into the Ti-6Al-4V substrate by using double glow plasma surface alloying technology and the burn-resistant alloyed layer was formed on the surface.
为解决整体阻燃钛合金存在的比强度低、加工性差及价格昂贵等问题, 利用双层辉光离子渗金属技术,在Ti 6Al 4V的表面渗入Cu元素, 在其表面形成Ti Cu阻燃合金层。
补充资料:镁铝锌系铸造镁合金
镁铝锌系铸造镁合金
magnesium-aluminium-zinc cast magnesium alloy series
mellUxlnx一zhuzao melhej一n镁铝锌系铸造镁合金(magnesium一alumini-um一Zine east magnesium alloy series)以铝、锌为主要合金化元素的铸造镁合金,可用于砂型和金属型铸造,也可用于压力铸造,具有良好的流动性和焊接性能,热裂倾向性低,但有较大的显微疏松倾向。 中国牌号ZM一5(7.5%一9.0%Al,0.15%一0.5%Mn,0.2%一0.8%Zn,Mg为余量)合金,ZM一10(9 .0%~1 0.2%AI,0.15%一0.5%Mn,0.2%一0.8%zn,Mg余量)合金。zM一5合金为镁铝锌系铸造镁合金的代表,相当于前苏联牌号的M月5合金。合金中杂质为铁、铜、镍、硅、钻等,根据需要可适量加些被。 铝是主要合金化元素并含有锌和锰,通过改变铝、锌含量可改变合金的力学性能、铸造性能及抗蚀性能。铝含量的增加能进一步改善合金的铸造性能和提高合金的强度,但使伸长率和抗腐蚀性能降低。加入少量的锌和锰能显著提高合金的抗蚀性能,还可以提高合金的强度。但锌含量增加会使合金的缩松倾向增加。ZM一5合金的铸态组织由固溶体叔Mg)为基体,沿它的晶界以不连续网状分布着y(Mg‘A13)相,以及分布在固溶体叔Mg)中的Mn一Ai化合物小质点所组成。热处理强化常采用两种规范:(1)淬火(T4):加热到370~380℃保温2一4h,再升温至415士5℃保温12一16h,然后在空气中冷却。(2)淬火时效(T6):淬火后再在175士5℃人工时效16h。ZM一5合金的力学性能见表1。 表1 zM一5合金的力学性能详 镁铝锌系铸造镁合金结晶间隔较大,充型能力良好,铸造工艺性能及物理常数见表2。表2 zM一s合金铸造工艺性能及物理常数}牛粉粉{字朴 镁铝锌系铸造镁合金能铸出外形和内腔形状复杂的铸件,加之镁合金在汽油、煤油、润滑油中很稳定,因而多用于航空工业的燃油系统和润滑系统。还可作为在受冲击载荷时能吸收大量能量的零部件及飞机着陆轮的轮毅。 (杨朴)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条