说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 过盈量
1)  magnitude of interference
过盈量
1.
The article analyzes characteristics and abrasion factor of leather cap type pig according operation feature, and then proposes reasonable magnitude of interference.
文章根据皮碗式清管器在钢质管道中的运行特点,分析了影响清管器皮碗的特性及磨损因素,给出了皮碗合理过盈量
2.
The maximum and the minimum magnitude of interference of the shield canister and the magnet steel hoop are calculated,and the shield and the magnet steel hoop are fitted by shrin.
文中还计算了屏蔽筒与磁钢箍热套配合的最大与最小过盈量,据此设计的电机转子现场热套和安装成功,实际工作转速可达8 000 r/min以上。
3.
By reducing the hydraulic oil pressure of the grinding roll in operation,enhancing the magnitude of interference fit between the roll core and the roll ring,and increasing the junction area between .
通过采取降低运行时磨辊液压油压力,增加辊芯与辊套的静配合过盈量,增加磨辊辊套与辊芯的结合面面积,使得辊芯与辊套的配合紧力加大了,减少了结合面产生松动的可能性,从而有效地防止磨辊辊芯与辊套的磨损、松动,避免因磨辊辊套的松动而导致辊套表面产生交变应力及承受较大冲击力而产生裂纹,延长磨辊辊套与辊芯的寿命。
2)  interference [英][,ɪntə'fɪərəns]  [美]['ɪntɚ'fɪrəns]
过盈量
1.
The finite element method is applied to simulate the cold expanding of the joint as well as the bell and spigot fitting process of internal and external pipes, therefore to determine the interference and overlapping length, analyze the joint forces and give the uniform strength condition of joint and pipe.
文章针对D159mm×8mm无缝钢管进行了压接工艺条件下力学计算与分析,利用有限元方法模拟无缝钢管冷态下胀口和内外钢管承插配合过程,确定了内外钢管对接承插过盈量及搭接长度,分析了压接接头的受力情况,给出了压接接头与钢管等强的条件,为压接接头配合参数设计及工艺试验提供了依据。
2.
The analysis results show tha t the larger interference between the spindle and the toolholder or a higher draw bar force is benefit to improving th.
研究表明 ,适当提高过盈量 (轴向拉力 )对于提高主轴 /刀柄联接特性具有积极意
3)  shrink range
过盈量
1.
Analysis and experiment of the optimum shrink range between chain plate and bush for agricultural machinery chain by using finite element method;
农机链链板与套筒最优过盈量有限元分析及试验研究
4)  excess [英]['ekses]  [美]['ɛk,sɛs]
过盈量
1.
This paper calculates the stresses, displacements, permanent bore enlargement, excess, degrees of autofrettsge and push force in secondary mechanical autofrettage technique of thick-walled cylinders with bilinear materials.
本文在文献[1]的基础上,针对作者首次提出的二次机械自紧技术,分析计算了双线性材料二次机械自紧厚壁圆筒的应力、位移、残余胀大量、过盈量与自紧度、冲头推力等二次机械自紧技术中的关键问题。
2.
In this paper,the crucial calculating formulas for stresses, displacements, excess, degrees of autofrettage, permanent bare enlargement and push force etc.
考虑了实际材料的应变硬化和Bauschinger效应,利用合理的简化假设、通过弹塑性分析,得到了计算机械自紧厚壁圆筒的应力、位移、过盈量与自紧度、残余胀大量和冲头推力等机械自紧技术的关键计算公式。
5)  Amount of interference
过盈量
1.
The research on amount of interference for shrink-on cylinder;
关于缩套圆筒过盈量的研究
6)  interference fit
过盈量
1.
Considering the interference fit between axle and wheel and mesh refinement in the high stress gradient zone,the influence of axle design parameters on the contact pressure between axle and hub is investigated.
这些参数包括过盈量、过渡圆弧半径、轮毂悬伸量、轮座与轴身直径比和空心度,以及使用条件下的摩擦系数、轮轴温度和轮对旋转速度。
2.
The driving gear for SDD8 diesel locomotive was redesigned through optimization of parameters,materials,heat-treatment and optimizing interference fit.
通过参数的优化、材料的选取、热处理的控制和压装过盈量的确定,对SDD8型机车的牵引主动齿轮进行了重新设计,期望该齿轮能达到机车运用1个大修周期的要求。
补充资料:虚盈
1.空和满。 2.比喻事物的盛衰﹑消长﹑兴亡等变化。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条