说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 凹模
1)  matrix [英]['meɪtrɪks]  [美]['metrɪks]
凹模
1.
The design method of faceplate oblique edge blanking die, die structure, punch structure and matrix structure were introduced in detail.
详细介绍了面板斜刃冲裁模的设计方法和模具结构及冲裁凸凹模结构。
2.
The method is introduced by combining slidable bending matrix with slidablebending punch to bend the border off lake parts after piercing blanking,the die structure issimple and ingenious,which can be referenced bysimilarproducts.
介绍了在冲孔落料后用可滑动折弯凹模与可滑动折弯凸模相结合对薄片形件进行弯边,模具结构简单、巧妙,对同类产品具有一定的借鉴作用。
3.
The cold upsetting matrix's life is relatively short in this way.
使用该方法冷镦凹模寿命低。
2)  die [英][dai]  [美][daɪ]
凹模
1.
Application of boronizing Cr12 steel in drawing die;
Cr12钢渗硼拉深凹模的应用
2.
Single Die's Design of Cold Extrusion;
冷挤压单层凹模材料优选
3.
In view of the forming process difficulty of the high precision part,the problems of the present cold extruding die,such as big flash and low service life were analyzed.
改进后的模具将凹模的结构形式由原来的整体式改变为分体式结构,即定位部分与凹模部分分开。
3)  concave die
凹模
1.
The drawing die structure of shirt oil bottom shell is introduced,the surrounding border of shirt oil bottom shell needs to be drawn at concave die and blank holder.
介绍了裙边油底壳拉伸模结构,裙边油底壳周边需在凹模和压边圈拉伸成形。
2.
The processing methods of compound punching die convex die concave die and die of convex and concave for silicon steel piece cemented carbide are provided.
介绍了硅钢片硬质合金复合冲模与凸模、凹模、凸凹模等的制造方法。
4)  cavity die
凹模
1.
The large type cavity die with thin wall belongs to blanking cavity die and punching work-piece is 20 cold rolled steel sheet.
薄壁大型腔凹模属于落料凹模,所冲压工件材料为冷轧20钢板。
2.
The reason that the fatigue failure is occurred in the early stage along the internal hole of the punching cavity die while punching is analyzed.
分析了冷冲压凹模工作时内孔边缘易发生早期疲劳断裂的原因 ,采用电火花强化工艺对凹模内孔刃口处进行局部强化 ,解决了凹模早期疲劳失效问题。
5)  female die
凹模
1.
Study on methods of controlling and adjusting clearance between the male die and the female die;
冲压模具凸凹模间隙控制与调整方法研究
2.
Cold upset female die of fillister head is the key mold in the manufacturing process of heading bolt.
冷镦圆头凹模是冷镦螺栓生产过程中的关键模具。
6)  female die
母模(凹模)
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条