1) grain size of α phase
初生α相尺寸
2) α size
α相尺寸
1.
The deformation mechanism of TC4 alloy with different initial α sizes of 6μm,12μm,20μm respectively has been investigated by isothermal compression tests in a temperatures range 890~950℃ and strain rates range 0.
1~10 s-1范围进行等温热压缩实验,并研究了初始α相尺寸对合金高温变形行为的影响。
3) primary α phase
初生α相
1.
Rheological behavior of semisolid A356 alloy with different morphology of primary α phases;
液固温区不同初生α相形态A356合金的流变行为
2.
The crack propagation behavior of primary α phase under tension and cyclic load has been observed in-situ by SEM for near-α type TA15 titanium alloy.
利用带载荷台的扫描电镜原位观察了近α型钛合金TA15中初生α相在单向拉伸和循环交变载荷下裂纹的扩展行为 ,结果表明 :单向拉伸时 ,由于初生α相强度高于基体 β转变组织 ,裂纹遇到初生α相时一般不能穿过而是绕过 ;而在交变载荷下 ,由于基体 β转变组织产生循环硬化 ,其强度水平与初生α相相当 ,裂纹遇到初生α相时可直接贯穿 ,并沿与应力垂直的水平方向扩展。
3.
It is shown that the cause resulting in the machining abnormality is coarse strip-shaped primary α phase.
针对钛合金TC4封装壳体加工异常的现象,从壳体的加工工艺过程、钛合金热轧板材化学成分、金相组织等方面进行了详细分析,判定壳体加工异常的原因在于材料中呈粗大长条状分布的初生α相,并分析了钛合金热轧板材中产生粗大长条状初生α相的原因。
4) Primary α-Al Phase
初生α-Al相
5) The primary α-Mg phase
初生α-Mg相
6) Domain Size
相区尺寸
1.
formation of ion cluster and the interfacial tension between two polymers, a theoretical equation for predicting the domain size in thermoplastic interpenetrating polymer networks was derived Small-angle X-ray scattering (SAXS) techniques were applied to measure the phase dimension via statistical treatment.
从聚合物混合的热力学基础出发,推导出SBS/聚(苯乙烯-甲基丙烯酸盐)热塑性IPN的相区尺寸与其组成的理论关系式。
2.
In this paper,we report quantitative determination of interphase thickness and domain size in poly(styrene)-block-poly(butadiene) and poly(styrene)-block-poly(butadine)-block-poly(styrene) copolymers(PS-PB and PS-PB-PS) by novel solid-state NMR methods developed recently in our group.
采用我们前期发展的测定多相高聚物中界面相厚度及相区尺寸的NMR新方法对两种不同嵌段结构的聚苯乙烯-聚丁二烯嵌段共聚物进行了研究,并与关于界面相厚度的高分子物理理论结果进行对比。
补充资料：初生不净
【初生不净】
谓十月满足，头向产门，流血淋漓，腥秽狼籍，故名初生不净。
谓十月满足，头向产门，流血淋漓，腥秽狼籍，故名初生不净。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条