1) thin strip
薄带
1.
Development of the thin strip tension-leveling;
薄带拉伸弯曲矫直技术研究进展
2.
Design of a multi-tooth plough formation device for machining micro-grooves on the surface of thin strip;
薄带表面微沟槽多齿犁削成形装置的设计
3.
Contact mechanics in cold rolling of thin strip;
薄带冷轧接触力学(英文)
2) strip
[英][strɪp] [美][strɪp]
薄带
1.
Effect of surface condition on AZ31B magnesium alloy strip ultrasonic welding;
表面状态对AZ31B镁合金薄带超声波焊接性的影响
2.
Formation of fine microstructures in twin roll cast stainless strip;
双辊铸轧不锈钢薄带中细小晶粒组织的形成
3.
Preparation of rapidly solidified 1050Al strip by double-belt method;
双带法快速凝固1050Al薄带的成形试验研究
3) ribbon
[英]['rɪbən] [美]['rɪbən]
薄带
1.
An experimental method of AFM investigation on ribbon′s cross-section;
用原子力显微镜观察薄带断面的实验方法
2.
A series of ribbon of Al-Zn-Si based alloy is prepared by using a single-roller quick-cooling equipment,and the melting point and wettability of brazing ribbon as well as the strength and microstructure of its welded joint are analyzed.
利用单辊急冷设备制备了系列Al Zn Si薄带钎料,并对其熔点、润湿性、接头强度及微观组织进行了分析。
3.
In the present paper,the giant magnetoimpedance effect of Fe 84 Zr 7B 9 ribbon has been investigated in detail.
详细研究了Fe84Zr7B9薄带中的巨磁阻抗效应。
4) tape
[英][teɪp] [美][tep]
薄带
1.
The tape-scraper tribosystem derived from ATM was used to study the wear behaviors of PEN(poly(ethylene-2,6-naphthalenedicarboxylate)) and PI(polyimide) tape under the falling sand dust environment with varied sand dust flow rate.
在实验室模拟降尘环境中使用ATM中的Tape-scraper摩擦系统,对PI(聚酰亚胺)和PEN(聚萘二甲酸乙二酯)两种高聚物薄带的磨损行为进行了研究,并利用扫描电镜对薄带的磨损表面进行了分析。
2.
Abrasive wear experiment of PEN(polyethylene2, 6-naphthalenedicarboxylate) tape was performed in sand dust environment with ATM(Auto Teller Machine) tribosystem.
选取聚萘二甲酸乙二酯(PEN)薄带在ATM自动取款机摩擦学系统中进行了沙尘磨粒磨损试验,利用表面形貌仪以一定时间间隔测量薄带磨损形貌,采用结构函数法考察磨损形貌的分形特征,并利用扫描电子显微镜分析其磨损机理。
3.
Abrasive wear characteristics of polymer tape of PEN (polyethylene-2, 6-naphthalenedicarboxylate) and PI (polyimide) due to sand particles was investigated at loads of 0.
模拟塔克拉玛干沙漠的沙尘环境,对(ATM)自动取款机摩擦学系统进行了磨损试验,分析了聚酰亚胺(P I)和聚萘二甲酸乙二酯(PEN)高聚物薄带在3种载荷以及有无纸币基体情况下的沙尘磨损性能和机理。
5) ribbons
[英]['ribən] [美]['rɪbən]
薄带
1.
Three kinds of AlSiCu alloys were melt spun into ribbons of about 70100u,m thickness.
利用单辊急冷设备,制得了厚度为70～100μm的三种Al-Si-Cu薄带钎料。
2.
Ni-Ti-Hf-Cu alloy thin films and have ribbons been fabricated by D.
本文分别采用直流磁控溅射技术和熔体甩带法制备了Ni-Ti-Hf-Cu合金薄膜和薄带。
6) melt-spun ribbon
快淬薄带
1.
Microstructure characteristics of the Sm(Co_(0.68)Fe_(0.20)Cu_(0.08)Zr_(0.04))_z(z=10,12)melt-spun ribbons;
Sm(Co_(0．68)Fe_(0．20)Cu_(0．08)Zr_(0．04))_z(z=10、12)合金快淬薄带的微观组织特征
2.
Four kinds of melt-spun ribbons with the compositions of NdxFe94-xB6 (atom percentagex=7,8,9,10) were prepared using the method of single roller rapidly quenching.
用单辊快淬法制备了成分为Nd_xFe_(4-x)B_6（x＝7，8，9，10）的四种快淬薄带，用X射线衍射（XRD）和Mossbauer谱对四种使淬苏带的非晶化程度进行了研究结果表明，Nd含量的增加可以提高材料的非晶形成能力快淬薄带的晶化行为和晶化产物分别用示差热分析（DTA），XRD和热磁测量进行了研究x≥8时，快淬薄带直接由非晶态晶化得到Nd2Fe14B和α－Fe两相；当x＝7时，快淬薄带的晶化是一个两步过程，首先生成中间相Nd2Fe23B3，然后经过中间相的分解，得到Nd2Fe14B和α－Fe。
3.
5Fe80NbB6 melt-spun ribbons,after isothermal crystallization processes at 943,973 and 1003 K,was studied.
5Fe80Nb1B6非晶快淬薄带在943,973和1003 K等温晶化与薄带组织和矫顽力的关系。
补充资料：板带轧制速度规程(见板带轧制规程设计)
板带轧制速度规程(见板带轧制规程设计)
speed schedule for plate and strip rolling
bandai zhazhi sudu guieheng板带轧制速度规程(speed seheduxe fo:plateand strip rolling)见板带札制规程设计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条