1) profile error
齿形误差
1.
Research on Coordinate Method for Measuring the Profile Error of Wormgears;
坐标法测量蜗轮齿形误差的研究
2.
Measuring the Profile Error of the Involute Gear;
齿轮渐开线齿形误差的测量
3.
The tooth profile error and longitudinal form error are calculated,and the change rule with setting angle of them is got.
针对花键的齿形误差和齿向误差,按照误差计算原理,得出了计算结果及其随安装角改变的变化规律。
2) tooth profile error
齿形误差
1.
Research on the tooth profile error of gear shaving;
剃齿加工齿形误差的研究
2.
Study of measurement of tooth profile error of circular tooth gears by rectangular coordinates method;
用直角坐标法测量圆弧齿轮齿形误差
3.
By means of analysis and calculation,the conclusion is given a spiral normal section on the pitch cylinder of a hob basic worm is different from another;If the normal sec- tion in the center of the tooth line is taken as a tooth measuring and design section,when spline hob is designed in a plane meshing,the tooth profile error is minimum.
通过分析并进行计算得出:同一滚刀基本蜗杆,节圆柱上不同螺旋线的法剖面截形有明显差别;如果以齿纹中点法剖面作为齿形检测和设计剖面,用平面啮合法设计花键滚刀时,则齿形误差最小。
3) tooth profile errors
齿形误差
1.
On the basis of deriving the calculating formula of tooth profile error, generates a solution of the optimurn tooth profile angle, which can keep the tooth profile errors smallest.
本文在推导出齿形误差计算公式的基础上,给出一种使齿形设计误差最小的最佳齿形角的求法。
4) tooth error
齿形误差
1.
Application of virtual instrument technology in gear tooth error testing system
虚拟仪器技术在齿形误差检测系统中的应用
2.
This paper presents a new method to measure tooth error of small module gears.
0 mm)进行测量,提出了一种在视觉三坐标测量机上测量小模数齿轮齿形误差的新方法。
5) tooth form error
齿形误差
1.
On-machine measuring method of tooth form errors of spiral bevel gears was investigated.
对大规格螺旋锥齿轮齿形误差的在机测量方法进行了研究。
2.
Non - zero orthogonal rake hobbing cutter produces large error by common grinding ways accoding to the chamge of tooth form error.
非零前角滚刀按常规方法重磨产生较大齿形误差，本文根据重磨齿形误差变化规律，用优化方法确定滚刀重磨参数，控制误差，提高滚刀重磨精度，增加滚刀的精度寿命。
6) total profile error
齿形误差
1.
Using a four-dimensioned universal installation with high precision that can control and measure temperature,an experiment program is designde in particular condition to measure the total profile error changed with temperature.
齿轮在工作温度和环境温度偏离标准温度后,其齿形会发生改变,引起齿形误差,而齿形误差又是影响齿轮传动平稳性的重要因素之一。
补充资料：齿形三角带
分子式：
分子量：
CAS号：
性质：又称同步齿形胶带。综合皮带、链条、齿轮等传动部件的优点。以钢丝或合成纤维做中心骨架层，工作面成齿形环状。一般是用液体聚氨酯橡胶浇注后经固化而成。也有以氯丁胶为主的。
分子量：
CAS号：
性质：又称同步齿形胶带。综合皮带、链条、齿轮等传动部件的优点。以钢丝或合成纤维做中心骨架层，工作面成齿形环状。一般是用液体聚氨酯橡胶浇注后经固化而成。也有以氯丁胶为主的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条