说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 脱模
1)  demoulding
脱模
1.
Development of two-step demoulding mechanism at side slide block of injection mould;
注射模侧滑块二级脱模机构设计
2.
Using the self setting resin sand to clean the inner surface instead of sodium silicate sand can hugely shorten the time of whole demoulding course,improve work efficiency and decrease working strength.
内腔用树脂自硬砂代替水玻璃砂,大大缩短了整个脱模过程的时间,提高了工作效率,降低了职工的工作强度。
3.
In consideration of the difference between two parts,insert blocks on moving half and fixed half were combined;and the compounded core-pulling of slanted pushing rod,dog-leg cam and slide block was applied to finish the demoulding of internal and external side concave.
介绍了1副在同1副模具中注射成型2个差异性较大的塑件的模具结构,该模具设计时综合考虑了2个塑件的差异性,分别采用了动、定模镶块组合的结构形式,并使用斜推杆、弯销与滑块复合抽芯来完成内外侧凹脱模
2)  demolding
脱模
1.
Three ways for demolding of plastic part with internal circle undercut;
整圆内侧倒扣塑件的3种脱模方式
2.
Study of the Demolding Process in Hot Embossing of Polymer Microfluidic Chip;
聚合物微流控芯片脱模过程研究
3.
The core-pulling and demolding mechanism of an injection mould for the deep cavity part were introduced.
分析了塑料桌腿塑件的结构和工艺特点,介绍了一种深腔注射模的抽芯和脱模机构,此机构运行安全可靠,自动化程度高,可为类似塑件的模具设计提供参考。
3)  stripping [英][strip]  [美][strɪp]
脱模
1.
when manganese ore powder are pressed to cold-press pellets by twinroller,it appears a serial of problems such as pack set,lack of feedstock,difficulty of stripping and so on.
针对锰粉矿压制冷压球团时压球设备(对辊压球机)出现结拱、喂料不足以及脱模困难等问题。
2.
The difficulty with stripping on paraffin wax has been analyzed from production process,feedstock and paraffin wax characteristic.
从生产工艺过程、原料及自身特性等方面对石蜡成型装置脱模困难的问题进行了分析,明确了其主要原因在于原料本身和石蜡的成型温度。
3.
A kind of simple and practical molding and stripping mechanism for plastic parts with inclined hole is introduced.
介绍了一种简单实用的塑件斜孔成型脱模机构 ,在不增加模具制造成本的前提下 ,巧妙地解决了斜孔脱模的难题 ,并讨论了应用范围。
4)  demould [di:'məuld]
脱模
1.
The structure characteristics and technology requirement of the washer sliding were analyzed, designed the injection mold with an ordinary injection system and three layers, solved the problem of automatic demould, the die structure and working process were introduced, practical production showed the die is safe and reliable, and it improved manufacturing efficiency.
分析了塑件的形状特点和技术要求,设计了一副普通浇注系统3层注射模,并解决了该注射模的自动脱模问题。
2.
By the analysis of the demoulding failure of the side slide of the injection mould andreferring to the principle of ejector pins moving, ejector pins were added in the side slide and thestructure of the ejector pins was improved.
通过对注塑模侧滑块脱模不良的分析,并参考动模顶出杆的顶出原理,在侧滑块上追加顶芯,再进一步改进顶芯的结构,使侧滑块顺利脱模
5)  liftout
脱模
1.
The study of parameters(helical angle and cone angle) of spiral bevel gears obtained effects on liftout processes.
近净成型技术是制造螺旋锥齿轮的发展方向,研究精锻螺旋锥齿轮参数(螺旋角和锥角)对脱模过程的影响,利用ADAMS软件的仿真功能进行模拟分析,从而判断螺旋锥齿轮脱模的可行性。
2.
Based on the simulation and analysis of software ADMAS,Cavity dies used in spiral bevel gears forging process were designed and liftout processes were simulated dynamically.
利用模拟分析软件(ADAM S)对凹模进行设计,并对脱模过程进行了动态仿真,在此基础上对锻件脱模可行性进行了研究和探索。
6)  pattern draw
脱模
1.
The performance of pattern draw of the spherical pits on the roll of the form-machine has direct influence on the regular function and the efficiency of the production line.
精铁粉冷压球团成形机是生铁冶炼炉料生产线的关键设备,其轧辊球坑的脱模性能直接影响生产线的正常工作及效率。
补充资料:脱模


脱模
stripping mold

  tU0mLJ脱模(s triPping mold)指将钢锭从钢锭模内脱出的一系列操作。钢锭浇注完毕至脱模的时间,从一桶钢最后一支(下注盘)钢锭浇注完毕至第一支锭开始脱模(脱帽)的时间称为钢锭的传搁时间。镇静钢钢锭,要求钢锭本体全部凝固方能开始脱保温帽,半镇静钢钢锭和沸腾钢钢锭的凝固层达到一定厚度即可脱模。各种钢锭在模内的传搁时间取决于钢锭的凝固速度或完全凝固时间,可根据经验计算或实验确定。小型钢厂生产单重3t以下的钢锭,一般以通用桥式起重机附加的脱模(锭)夹具或吊具完成脱模作业。用车注法生产大钢锭的钢厂在脱模跨间采用脱模(锭)机作业。 脱模(锭)机基本任务是处理不同形状、尺寸和单重的钢锭,完成以下工艺操作:自由或强制脱模、脱保温帽、脱锭;自由或强制取下底板上的钢锭。现有的脱模机,多数依靠静力作用在起重机械上装配的夹扯和推顶专用工具。通过夹钳的开闭与提升运动和钢锭、钢锭模的重力作用完成各种自由脱模、脱帽和脱锭作业,利用推顶工具的顶、挡及与夹扯工具之间的相对直线运动而进行强制脱模(脱锭)作业。常用的脱模机为桥式(或半龙门式、地上走行式)脱模起重机,有的钢厂也装有地上(固定式)脱模装置。桥式脱模起重机的工作能力一般用强制脱模能力、自由脱模(起重)能力和辅钩起重能力表示。根据钢锭重量选定脱模机的能力,可参照以下经验公式: P=(10一20)Q或P=75+IOQ式中p为脱模机工作能力,t;Q为钢锭单重,t。前苏联设计的系列脱模机的主要参数如下:规格/t 275/25/25250/50/25钢锭重/t 1015额定脱模能力八175 250最大过载出力/t 500~700750~1000大钳起重能力/t 2550辅钩起重能力/t 1525桥式脱模起重机的操作功能及夹钳形状见图。自由脱模使用大钳;自由脱锭使用小钳;强制脱模时下降顶杆顶住钢锭用大钳脱模;强制脱锭时则用大钳制止模子_随锭上升。地上脱模机一般只用于处理锭一模粘连预脱锭失败的上大下小钢锭,其操作是:用一对夹钳夹持模子下耳使之固定不动,开动顶杆使之上升伸入模子底孔,利用顶杆的顶推力撕开粘连部分将钢锭顶出钢锭模。裂如 桥式三用脱模起重机强制脱模机构 所能完成的技术操作 a一用大钳及顶杆强制脱上小下大的钢锭;b一用大错及小钳强 制脱上大下小的钢锭;c一脱最大高度的钢锭:己一用大钳脱保 温帽;。一当模子双排放置时脱上大下小的钢锭;了二用小钳及 大钳将_上小下大的钢锭由底板上扯起 1一顶杆;2一大钳;3一小钳 脱模工艺车铸的各类钢锭的脱模工艺各不相同。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条