1) blowing-in
开炉
1.
Successful blowing-in of No.3 1750m~3 blast furnace in ji'nan Iron and Steel Co.;
济钢3号1750m~3高炉开炉达产达效实践
2.
The experiences on blowing-in and reaching target output of 2500m3 BF in NISCO are summarized.
对南钢2500m3高炉开炉及快速达产进行了总结。
3.
The details of blowing-in of Tanggang No.
对唐钢1号高炉扩容大修改造、开炉及快速达产经验进行总结。
2) blow-in
开炉
1.
For the purpose of further developing the blow-in technology and improving the BF technico-economic indexes,some important management measures and technical preparations,including the management system for the blow-in,drying of the hot stove and blast furnace,burden filling in,blasting control,slag performance adjustment,etc.
为进一步发展高炉开炉技术,提高高炉各项技术经济指标,回顾了宝钢4#高炉开炉前的主要管理措施和技术准备内容,包括开炉管理体制、热风炉和高炉烘炉、炉料填充、送风控制、调整开炉炉渣性能等。
2.
151 t/(m3·d) on day 5 after its blow-in.
济钢1#1 750 m3高炉项修开炉,由于对原燃料质量及用料结构等准备充分,风口进风率及布料矩阵等操作参数选取得当,开炉过程中下料顺畅,无悬料,恢复进展快,实现了开炉第5天利用系数达2。
3.
Due to the reasonable schedule of furnace drying out and blow-in operating,as well as correct parameter choosing,the blast furnace reached designed capacity.
由于制定的高炉烘炉、开炉方案合理,操作参数选择得当,高炉开炉后4d达产,利用系数2。
3) blowing on
开炉
1.
7 blast furnace(450 m3) reached its output rate in 3 days following the blowing on after its middle repair.
宣钢7号高炉(450m3)中修后通过充分准备、制订合理方案、精心操作,在开炉后3天达产,创造了宣钢开炉达产的最好水平。
2.
of this plant, in the overhaul of 2# blast furnace of south area of Ironworks of Tang Steel a whole and thorough reformation is applied to all unreasonable equipment and process, a new blowing on method adopted to fully open tuyere, fill up railway sleeper and charge statically.
唐钢炼铁厂南区2#高炉(450m3)充分吸取了唐钢前两座高炉设计、建设及投产过程的经验教训,对各种不合理的设备工艺环节进行了全面彻底的改造,并采用全开风口、枕木填充静态装炉方法开炉,取得了10天之内达产的良好效果。
3.
The whole preparation and blowing on operation of 2# blast furnace Cheng Steel are instroduced.
介绍承钢450m3高炉开炉前的准备及开炉操作全过程。
4) blowing in
开炉
1.
The operative ways of blowing out and blowing in at item repair of Jigang No.
介绍了济钢 2 #高炉项修时的停炉、开炉操作方法。
2.
And after blowing in on its first test run being successful and becoming normal, the utilization coefficient of the first month has reached 3.
济钢 6#高炉在炉底侵蚀严重、炉墙结厚的情况下 ,通过优化方案、强化施工网络管理等措施 ,使大修改造工期仅用3 8天 ;在一次开炉成功并迅速达产后 ,当月实现利用系数 3 。
3.
How to successfully put an evaporated cooling system of a converter flue in operation and establish the relative stable operation were important contents when blowing in of a converter.
如何使转炉汽化冷却系统顺利投产,建立一个相对稳定的工况,是转炉开炉时的一个重要内容,介绍了马钢一炼钢95t转炉汽化冷却系统首次开炉工艺。
5) blow in
开炉
1.
288 on the 3rd day since blow in.
攀钢2号高炉(1200 m3)第三代炉役扩大性小修于2005年3月15日开炉,此次开炉由于采用了快速烘炉、带风装料、炉底多点送风点火、优化炉料结构等技术,开炉后设备故障少,炉缸活跃,加风顺利,炉况顺行。
2.
The blow in and operation for Pangang 2 #blast furnace were introduced.
介绍了攀钢２＃高炉开炉达产的情况。
3.
When blow in is used of all coke,the suspending burden is easily produced in No.
莱钢第一铁厂采用全焦开炉时，开炉过程易产生顽固性悬料。
6) furnace selection switch
炉选开关
补充资料：开炉
【开炉】
（行事）禅林阴历十月一日开炉，此日方丈有大相看。敕修清规月令须知曰：“十月初一日开炉，方丈大相看。”
（行事）禅林阴历十月一日开炉，此日方丈有大相看。敕修清规月令须知曰：“十月初一日开炉，方丈大相看。”
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条