1) foaming slag
泡沫渣
1.
Application of foaming slag in LF processand its control in VD process;
LF VD过程泡沫渣的应用与控制
2.
The cause of foaming slag generated by Ausmelt converting furnace was analyzed concisely.
简要分析了Ausmelt吹炼炉泡沫渣发生的原因,同时提出了相应的预防措施。
3.
This paper introduces the phenomenon and reason of the foaming slag during smelting electrical furnace to produce zinc powder,describes the measure for prevent and treatment during production.
介绍了矿热电炉生产锌粉过程中泡沫渣产生的现象及原因,详细叙述了实践中采取的预防和处理措施。
2) foamed slag
泡沫渣
1.
Rational Technique for Foamed Slag in a 150t Arc Furnace;
150t电弧炉泡沫渣的合理工艺
2.
Operation of Submerged Arc in Foamed Slag of Ladle Furnace;
40t钢包炉泡沫渣埋弧作业
3.
In order to recycle the BF dust, reduction kinetics of FeO during the formation of foamed slag by adding BF dust and pitch coke to EAF was investigated.
为了循环利用高炉粉尘,研究了用宝山钢铁股份有限公司高炉粉尘与沥青焦粉混合后加入电弧炉造泡沫渣过程中FeO的还原动力学。
3) foam slag
泡沫渣
1.
The reduction of FetO by CO in foam slag was investigated.
考察了ＣＯ流量、添加焦炭颗粒和表面活性组元Ｐ２Ｏ５对泡沫渣中ＣＯ还原ＦｅｔＯ的影响。
4) foamy slag
泡沫渣
1.
The foamy slag technology was improved integrating with the production practice of the Xin Jiang Ba Yi iron & Steel Co.
结合新疆八一钢铁股份公司电炉厂的生产实际,在对泡沫渣发泡原理进行了比较透彻的分析,取得了明显的效果。
2.
Concerning melting process of UHP DC EAF, the research directions of metallurgists are how to organically integrate foamy slag practice, submerged arc heating, greater ratio of molten metal, avoidance of spouting as well as longer life of furnace lining.
简要介绍了新 70 t DC炉泡沫渣技术所进行的突破性研究与实践结果。
3.
This article introduces the technological feature and applied result of the new type multi functional slag door lance for EAF By using it,the power consumption is saved by 31 kW·h/t, and tap to tap time is reduced by 5 min,cost is reduced by 32 yuan/t Meantime,coal powder can replace coke sphere to produce foamy sla
同时试验证明采用煤粉可代替碳粉造泡沫渣。
5) slag foaming
泡沫渣
1.
The measures included higher hot metal ratio,slag foaming,endpoint carbon control and application of RBT process in EAF,atmosphere control,formation of good white slag and suberged arc operation in LF,and adoption of long ceramic nozzle and argon sealing between ladle and tundish to prevent against nitr.
介绍了安钢第一炼轧厂电炉炼钢工艺流程在冶炼低氮高强度船板钢时采取的主要技术措施,包括电炉提高铁水比、造泡沫渣、终点碳控制、RBT;LF精炼炉气氛控制、造好白渣、埋弧操作;钢包长水口及氩封保护浇注,防止连铸过程钢液吸氮。
6) foamed slag-forming
造泡沫渣
补充资料：高炉泡沫渣
高炉泡沫渣
the foaming slag of blast furnace
一定值后会有大量气体以气泡形式分散于渣中使炉渣的体积膨胀‘这种炉渣即为泡沫渣，它是特殊矿冶炼高炉造渣的一个重要问题。泡沫渣的产生将造成高炉生产过程渣铁出不尽，料柱透气性恶化，风口易挂渣，给高炉炉况顺行和强化带来困难。当炉渣进入渣罐后由于其体积膨大使渣罐利用率降低，甚至从渣罐上部溢出，造成事故。泡沫渣的形成有两个条件，一是有大量的分散气体生成，二是炉渣性能使分散气体稳定存在，从而使渣中气体量不断增加。在钒铁磁铁矿的高炉冶炼中，高炉下部有较多的Feo、TIO:等氧化物从渣中还原，从而产生大量CO气体。同时，高钦型高炉渣表面吸附，富集的活性物质比普通渣高得多。表面活性物.的存在使液膜的表面私度比体积豁度高，从而阻碍了排气速度，延长了泡沫的寿命。表面活性物的存在又使炉渣表面张力大大下降，造成渣内分散气泡合并上浮困难，使气泡更稳定，从而形成泡沫渣。解决泡沫渣间题的办法是采用一切手段提高渣中“氧势”，抑制TIOZ还原，减少Ti(C、N)等胶质微粒的生成，也即减少表面吸附的活性物质量，从而阻止泡沫形成。goolu Paomozha高炉泡沫渣(the foaming、lag。f blast fur-nace)高炉冶炼钒钦磁铁矿时，炉渣中Tio。高达
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条