1) anodic polarization
阳极极化
1.
Effect of sulfate ions on anodic polarization behavior of nanocrystalline copper bulk
SO_4~(2-)对块体纳米晶铜阳极极化行为的影响
2.
Kinetic analysis on anodic polarization behavior of nanocrystalline copper in Na_2SO_4 solution
纳米晶铜在Na_2SO_4溶液中阳极极化动力学分析
3.
The electrochemical behavior of AZ31 Mg alloy was investigated by measuring anodic polarization curves and electrochemical impedance spectroscopy(EIS).
采用阳极极化和电化学阻抗谱(EIS)技术研究了AZ31镁合金的电化学腐蚀行为。
2) anode polarization
阳极极化
1.
The corrosion behaviors of Ni-P/Si_(3)N_(4) composite deposit in acetic acid(w=20%) were studied by anode polarization curves,alternating current impedance and corrosion weight-loss test.
通过阳极极化曲线、交流阻抗谱和腐蚀失重实验研究了化学镀N i-P/S i3N4复合镀层在20%醋酸溶液中的腐蚀行为,并用SEM观察腐蚀前后镀层的形貌。
2.
With the X ray diffraction of these coatings contained different percentage of nickel, anode polarization action of the coatings during polarizing are analyzed.
对锌镍合金钝化及未钝化镀层在5%盐水及矿井水中的阳极极化曲线进行了测试,结合不同镍含量镀层的相结构衍射结果,分析了各镀层在极化过程中的阳极极化行为,讨论了锌镍合金耐腐蚀性优于纯锌镀层的原因。
3.
The results shows the capacity of the anode oxidation membrane decreases with the increasing of oxidation potential,and there exists relationship between impedance and behavior anode polarization.
提出了钽的氧化反应式及反应控制步骤 ;得出其氧化膜电容量随着氧化电位的增加而减少 ,阻抗与阳极极化行为存在相关关系。
3) negative anodic polarization
阴、阳极极化
4) anodization
阳极处理，阳极化
5) anodic treatment
阳极处理;阳极化
6) anodizing
[英]['ænəudaiz] [美]['æno,daɪz]
阳极化
1.
Analysis of abnormal surface colour of forged LF6 flange after anodizing;
锻造LF6法兰阳极化后表面深灰色原因分析
2.
The Phosphoric Acid Anodizing of Aluminum Alloys and the Analysis of its Adhesive Properties;
铝合金磷酸阳极化和胶接性能分析
3.
The effect of sulfuric acid,chromate acid and boric/sulfuric acid anodizing on fatigue performance of aeronautic aluminum alloys was studied by using S-N curve.
采用S-N曲线研究硫酸阳极化、铬酸阳极化和硼酸硫酸阳极化对航空铝合金疲劳极限的影响。
补充资料：环状阳极极化曲线
分子式：
CAS号：
性质：钝性金属在含有氯离子的溶液中，用稳态慢速电位扫描方法，先向正电位方向，然后再向负电位方向扫描所测得的呈环状的阳极极化曲线。如图示(图暂缺)。Eb为孔蚀击穿电位，此时钝化膜开始破坏产生孔蚀；Ep为孔蚀保护电位，此时钝化膜重新愈合修补好，金属恢复钝态。这是表征金属对孔蚀敏感性的两个基本电化学参数，可评价金属的孔蚀倾向。
CAS号：
性质：钝性金属在含有氯离子的溶液中，用稳态慢速电位扫描方法，先向正电位方向，然后再向负电位方向扫描所测得的呈环状的阳极极化曲线。如图示(图暂缺)。Eb为孔蚀击穿电位，此时钝化膜开始破坏产生孔蚀；Ep为孔蚀保护电位，此时钝化膜重新愈合修补好，金属恢复钝态。这是表征金属对孔蚀敏感性的两个基本电化学参数，可评价金属的孔蚀倾向。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条