1) bar
[英][bɑ:(r)] [美][bɑr]
棒材
1.
Finite Element Analysis of Bar Temperature Field During Water-Cooling;
棒材穿水冷却过程温度场有限元分析
2.
The contrastive research of force of bar extrusion deduced by upper bound theorem in two coordinates;
两种坐标系下上限法求解棒材挤压变形力的对比研究
3.
Development and application of groovless rolling technology of blooming mill for bar;
棒材粗轧机组无孔型轧制技术的开发与应用
2) rod
[英][rɔd] [美][rɑd]
棒材
1.
Preparation of superparamagnetic hydroxyapatite/chitosan rod;
超顺磁性羟基磷灰石／壳聚糖棒材的制备
2.
Analysis of the controlled cooling of rod rolling;
棒材连轧厂水冷材生产分析
3.
Analysis on defect essence of part worked with 2A50 aluminium alloy rod;
2A50铝合金棒材机加工零件上缺陷的分析
3) bar steel
棒材
1.
Study of automatic counting in on-line production of bar steel;
棒材生产在线计数问题的研究
2.
Pattern recognition based on the fusion technique for counting of bundled bar steel;
基于融合技术的棒材定支数图像识别
3.
Improvement of precision of bar steel rolling size and performance forecast requires the bar steel precise counting.
随棒材轧制尺寸精度和性能预报准确程度的大幅度提高,对棒材的精确计数要求也越来越高。
4) steel bar
棒材
1.
The principle is at first,the linear laser beam is projected vertically on steel bars on cooling bed,and then the laser beam images of steel bars are captured by a CCD area-scan camera,after laser beams are thinned,the contour coordinates of steel bars are calculated with BP neural networks.
提出将线型激光垂直照射于处于冷床上的棒材,通过面阵CCD摄像机采集激光图像,并对激光线条进行细化处理后,用BP神经网络计算并恢复棒材截面上部分轮廓的空间坐标。
2.
Because of the particularity of the steel bars and its producing arts,automatic counting of steel bars can t be settled for long time.
采用图像处理计数方法与光电计数方法相结合,利用集散控制系统的控制方案,开发出适合我国钢铁企业的棒材自动计数系统,可以有效提高计数准确度和生产效率,实现棒材计数过程的自动化和打捆的标准化,减低棒材生产成本,使生产利润最大化。
3.
The profile images of bundled steel bars are captured by area scanning CCD cameras, and gray level images are transferred into binary images by adequate threshold, and holes caused by grease on steel bar and joints between bar regions are eliminated.
利用面阵 CCD摄象机采集打捆后棒材的端面图象 ,通过合适的阈值将灰度图象转换成二值图象 ,以消除棒材图象区域中由于油污造成的孔洞和棒材区域间的粘连现象。
5) bars
[英][bɑ:z] [美][bɑrz]
棒材
1.
Inquisition about New Ultrasonic Testing Method for High Temperature Alloy Bars with Small Diameter;
高温合金小直径棒材超声检测新方法探讨
2.
Influential rule of cooling water flow on the cooling effect of big bars
冷却水流量对大直径棒材冷却效果的影响规律
3.
The bars of TC21 alloy with a diameter of 90mm were produced by α+β and β processing.
分别采用α+β锻造和β锻造方式制备了TC21合金90mm棒材,研究了两种加工方式下同规格棒材的裂纹扩展速率,分析了粗细两种片层结构对裂纹扩展速率的影响。
6) bar material
棒材
1.
Forming characters of Fe_(80)P_(13)C_7 amorphous coating fabricated by bar material plasma spraying;
棒材等离子喷涂法制备Fe_(80)P_(13)C_7非晶态合金涂层的成形特征
2.
a method of making Fe80P13C7 amorphous coating by bar material plasma spray, Analyzed the micro-structures of the coating, and crystallization temperature micro-hardness are tested, and we analyzed the constitution of front face and cross section of the coating by energy spectrum analysis.
采用棒材等离子喷涂法制备Fe80P13C7非晶态合金涂层,分析了涂层的组织,测定了晶化温度、显微硬度,采用扫描电镜观察涂层的微观形貌和截面形貌,能谱分析涂层正面和截面的成分变化,结果表明:制备的非晶涂层组织致密,均匀,涂层与基材之间为冶金结合与:机械结合相结合共同作用的成型特征;非晶涂层的显微硬度达946-1018HV25,晶化温度为433℃。
3.
A design for different kinds of defects to bar material to used ultrasonic was described in this paper.
本文介绍了一种对棒材的不同缺陷使用超声波检测的设计方案,该方法来源于工程实际,操作方便,检测速度快,判断准确率较高。
补充资料：棒材步进式冷床(新沪钢厂)
棒材步进式冷床(新沪钢厂)
棒材步进式冷床(新沪钢厂)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条