1) moisture content
湿含量
1.
The Analysis, Design and Debugging of the Moisture Content Controlling System of the Corned-Powder in the Spray-drying Tower;
喷雾干燥塔粉料湿含量控制系统的分析、设计与调试
2.
At last, it sets up the micromathe matical model of temperature distribution and the moisture content count abeut ceramics product in the drying pmeess.
本文分析了辊道窑内预干燥带传热及干燥过程的特点，引入Morgan的蒸发面后退模型，建立了陶瓷制品干燥过程中温度场分布及湿含量计算的微观数学模型。
3.
Experiments or measurements were then performed to obtain the particle size distribution,moisture content,apparent density,tap density,angle of repose,angle of internal friction,angle of straight carbon steel wall friction,angle of Perspex wall friction and(cohes.
以神府烟煤煤粉为研究对象,对其粒度、湿含量、松动密度、振实密度、休止角、内摩擦角、碳钢壁摩擦角、有机玻璃壁摩擦角、粘聚力进行全面测试分析。
2) wet basis moisture content
湿基湿含量
3) wetness fraction
湿度，含湿量
4) water content
含湿量;湿度
5) moisture content
含湿量
1.
Experimental investigation on the effects of moisture content and fibers on both explosive spalling and residual mechanics of high performance concrete(HPC) after exposure to high temperatures was presented in this paper.
本文研究了含湿量和纤维对高性能混凝土高温爆裂和高温后残余力学性能的影响。
2.
The method for determining the moisture content of air on airway surface was improved and the relationship between saturated moisture content of air and temperature was fitted into a quadratic curve.
笔者采用湿度系数法对壁面水分蒸发进行了处理,对计算壁面处饱和空气含湿量的方法进行了改进,将饱和空气含湿量与温度的关系拟合为二次曲线;建立了在考虑壁面水分蒸发情况下解算巷道围岩温度场分布及围岩向风流的散热量的数学方程,并采用异步长有限差分法对其进行了数值模拟求解;解算出巷道壁面水分蒸发情况下围岩温度分布、壁面温度和围岩散热量的变化规律;并与将饱和空气含湿量与温度的关系拟合为线型关系曲线时的解算结果进行了对比,将饱和空气含湿量和温度之间的关系拟合为线性的计算结果存在一定的误差,通风时间越长,湿度系数越大,风流相对湿度越小,拟合为线性时计算出来的壁面温度和围岩散热量的误差越大。
3.
Experimental investigation on the effects of moisture content and fiber on both explosive spalling and residual compressive strength of high performance concrete(HPC) after exposure to high temperatures was presented.
研究了含湿量和纤维对高性能混凝土高温爆裂及高温后残余抗压强度的影响。
6) humidity
[英][hju:'mɪdəti] [美][hju'mɪdətɪ]
含湿量
1.
The effects of the operational and the structural parameters on the desulfurization efficiency and gas humidity with the falling film desulphurization device are studied, including gas velocity, inlet gas temperature, SO2 concentration, the shape of nozzle, etc.
针对液柱射流式脱硫反应器,进行了烟气流速、入口烟气温度、入口SO2浓度等运行参数和结构参数对烟气含湿量和脱硫效率的影响的试验研究。
2.
The effects of the bed loading, velocity of the gas passing through the bed, relative humidity of the gas, and the sulfur dioxide concentration in the inlet gas on the effeciency of sulfur removal have been investigated in particular.
主要研究了床重、床速、床内气体含湿量和入口烟气中ＳＯ２浓度对脱硫效率的影响。
补充资料：湿含量
分子式：
CAS号：
性质：固体的湿含量是单位质量固体中所含的湿分（水分）质量，以干基或湿基表示。干基湿含量为单位质量干固体所含的湿分质量；湿基湿含量则指单位质量湿固体所含的湿分质量。若前者以Wd表示，后者以Ww表示，则两者的关系为：
CAS号：
性质：固体的湿含量是单位质量固体中所含的湿分（水分）质量，以干基或湿基表示。干基湿含量为单位质量干固体所含的湿分质量；湿基湿含量则指单位质量湿固体所含的湿分质量。若前者以Wd表示，后者以Ww表示，则两者的关系为：
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条