1.
Structure design and tube-weld cladding manufacturing technology for copper-clad steel wire
包覆焊接法铜包钢线的结构设计和生产工艺
2.
Research on Change Rule of Cladding Rate of Hot-rolled Aluminum Matrix Brazing Sheet
热轧铝基钎焊板包覆率变化规律研究
3.
3. Apply flux to outside of tube and inside of solder cup. Surfaces to be joined must be completely covered. Use flux sparingly.
3. 在管道的外面和焊接罩的内部涂上焊剂,焊剂必须完全覆盖焊接表面。请有节制地使用焊剂。
4.
apply flux to outside of tube and inside of solder cup. Surfaces to be joined must be completely covered. Use flux sparingly.
在管道的外面和焊接罩的内部涂上焊剂,焊剂必须完全覆盖焊接表面。请有节制地使用焊剂。
5.
Nickel-Based Alloy Powder Welding Properties of Laser Cladding
镍基合金粉末的激光熔覆焊接性能研究
6.
Over-application of ZSS010 will result in increased levels of weld fume on cutting and welding, and will also increase the porosity of the welds.
如果涂覆过厚，切割和焊接时会产生大量的焊烟，并增加焊接处的孔隙。
7.
Automatic Weld Parameter Set-Up including Pnelmate screen display.
焊接参数自动设定,包括盘面屏幕显示
8.
These include gusset plates welded to the flange.
这些包括焊接到翼缘上的节点板。
9.
Butt welded 1;Butt welded 2;Butt welded 3;Butt welded 4
对接焊接 1;对接焊接 2;对接焊接 3;对接焊接 4
10.
For all processes, the Welding Procedure Specification (WPS) shall contain a detailed cleaning procedure indicating joint preparation prior to welding.
对于所有焊接方法，焊接工艺规程都应详细包含清除方法，说明焊前坡口的准备。
11.
Are AOI/ AXI complementary methods, which include solder joint inspection, used for all reflowed parts?
AOI/AXI的检验方法包括焊接点的检验,是否用于回流焊元件检测?
12.
Rapid prototyping technique and its system development based on 3D welding cladding
基于三维焊接熔覆的快速成形技术及其系统的发展
13.
Analysis on Repairing Welding Procedures of A Boiler Vessel Tube
电厂锅炉汽包短管修复焊接工艺论证分析
14.
Lighting pole welding deformation control in beacon engineering at Baotou Stadium
包头市体育场灯塔工程灯杆焊接变形控制
15.
It is imperative that no heat is applied to connection as nipples contain a plastic liner.
如果螺纹接头包含塑料衬垫,则不要在这种螺纹接头上焊接。
16.
bare the end of a wire,ie strip off the covering of rubber,etc before making an electrical connection
剥开电线的端部（剥去包覆的橡皮等以便接线）.
17.
Likelihood Ratio Identification Method for the Detection of Adhesive State of the Liner Cladded in the Rocket Motors
火箭发动机包覆粘接状态检测似然比识别方法
18.
Study on Preparation of the Radical Grafting Polymerization of MMA onto Inorganic Nanocomposite;
无机纳米粒子表面接枝包覆PMMA的制备研究