1.
Transfer Behavior Study in Weld Thickness Direction of the Welding Plastic Metal in Friction Stir Welding
搅拌摩擦焊焊缝塑性金属在焊缝厚度方向的迁移行为研究
2.
"Where thickness characteristics at the joint are more important than strength, a thinner welder is possible at reduced joint strength. "
如果焊缝的厚度比强度更重要,则在降低强度条件下可使焊缝更
3.
Research on Weld Toughness of X80 Heavy Section Pipeline Steel at Different Welding Speeds
X80厚壁管线钢不同焊接速度下焊缝韧性研究
4.
Application of Multizone Ultrasonic Inspection for Great Thickness EBW
应用超声多区聚焦技术检测大厚度电子束焊缝
5.
"High strength steels may result in increased thickness, however, the resulting joint is strong, smooth and recoilable. "
高强度钢可能更厚些,但是,焊缝是强固的,平滑的,可重卷的。
6.
Decrease the weld number as possible: Choosing the right thickness of steel plate can reduce the rectification amount after welding!
尽可能的减少焊缝数量:适当选择板壁的厚度,可减少焊后变形矫正量。
7.
Judge of Transverse Crack of Thick-Walled Seam by Ultrasonic Testing Method
厚壁焊缝横向裂纹的超声波判别方法
8.
Forming limit and weld seam movement of TWBs with different thicknesses in square cup
差厚拼焊板拉深方盒形件成形极限及焊缝移动
9.
Microstructure and performance of friction stir welding in 6063 aluminum alloy
5mm厚6063铝合金搅拌摩擦对焊焊缝组织分析
10.
Indicates concave, convex or flush welds. Increase height to fit above other weld symbol.
指示凹焊缝、凸焊缝或平焊。增加高度以配合其他焊接符号。
11.
Regression and Analysis on Metal Strength of Welding Seam of Welding Core Wine
药芯焊丝焊缝金属强度的回归与分析
12.
Study of Length Calculation of Three Side Welded Lap;
三面围焊搭接角焊缝长度计算的探讨
13.
As for welding seams of the same heat treatment state, the hardness of welding seam area depends on different welding wires.
对于同一种热处理状态的焊缝,焊缝区的硬度取决于不同的焊丝。
14.
Control of Uniforming Compositions for the Large Thickness Joints of the Titanium Alloy
厚板钛合金电子束焊缝的成分均匀性控制
15.
Investigation into Ultrasonic Testing of Thick Walled Austenitic Welds
厚壁奥氏体焊缝超声波检测之探究(英文)
16.
Research on shrinkage regularity of butt weld of variable thickness steel plates for Zhengzhou Yellow River Bridge
郑州黄河桥不等厚对接焊缝收缩规律研究
17.
Wave Mode Conversion on Welding Ultrasonic Testing for Middle or Thick Plate
中厚板焊缝超声波探伤中的波型转换辨析
18.
Study on the Welded-line Movement of Square Cup Using TWBs in Hydro-forming Deep Drawing
差厚拼焊板方盒形件充液拉深中焊缝移动的研究