1.
The analytical method of kinetic characteristics of cam mechanism of swinging follower with fixed cam
固定凸轮的摆动从动件凸轮机构运动特性分析方法
2.
Optimum Design of Fixed Cam and Connecting Bar Mechanism Based on MATLAB
基于MATLAB固定凸轮与连杆组合机构的优化设计
3.
Loosen setscrews 2 in the vertical driving cam.
拧松上下传送凸轮的固定螺丝2。
4.
If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.
若正时链不令人满意,则拆下凸轮轴链轮固定螺栓,并拆下曲轴和凸轮轴链轮的正时链。
5.
Loosen two setscrews 5 in top feed cam 4.
拧松上送布凸轮4和固定螺丝52个螺丝。
6.
Cams are fastened on the fixture by screws, and the inside transmission system rotates cams to puch crank arms to change the position of slides.
凸轮固定在旋轮轴上,可以螺丝调整前后,并用以推动滑座之运动。
7.
Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条。
8.
Using a short piece of pipe and Holder 6958 to hold the pinion yoke, or pinion flange, remove the pinion nut and washer.
用短管和托架6958固定小齿轮轴轭或小齿轮凸缘,拆下小齿轮螺帽和垫圈。
9.
Each unit has a pair of cams, with an anti - friction roller for each cam.
每两对凸轮之间有一定的间隔,每一组凸轮中包括一对凸轮,每个凸轮对应一个减摩转子。
10.
system of fast and loose pulleys
固定轮及游滑轮系统
11.
Turn the top feed cam until it reaches the position to allow the three components such as the throat plate surface, top end of needle eyelet and presser foot (pressing plane) to align, and fix the cam at that position.
在针板上面、针孔上端、中压脚(压脚面)的3点对齐的位置,转动上送布凸轮,然后固定。
12.
DETERMING THE MINIMAL RADIUS OF BASE CIRCLE OF A CAM WITH TRANSLETINGA POINT FOLLOWER ACCORING TO THE ALLOWABLE PRESSURE ANGLE[α]
按许用压力角(α)确定直动从动件盘形凸轮机构凸轮最小基圆半径
13.
The Fix Method of Basic Size of Cam in the Disk Cam Mechanism with Straight Follower
直动从动件盘形凸轮机构中凸轮的基本尺寸确定方法
14.
overhead cam shaft
上凸轮轴上部凸轮轴
15.
Determination of Curvature Radius of Cam Profiles Using Numerical Differentiation
确定凸轮廓线曲率半径的数值微分法
16.
Using precisely graduator of cam,hypo-mood position fixing accurately.
采用精密凸轮分度器,下模定位精确。
17.
Quantitative Evaluation and the Geochemical Responses of Gas Washing in Lunnan Petroleum Province
轮南低凸起气洗作用响应及定量评价
18.
Development of Program Drawing the Contour Curve of Plate Cam at the Designated Point with AutoCAD VBA;
定点绘制盘形凸轮轮廓曲线的程序开发