1.
Study on Front Extreme Position of Beating-up Reed of Four-bar Beating-up Mechanism;
四连杆打纬机构打纬筘前心位置的分析与研究
2.
Analysis of reed-base′s front extreme position for four-bar beating-up linkage
四连杆打纬机构的筘座前心位置分析
3.
Beat -up is accomplished by the use of wire grate called a reed.
打纬是由一个被称为钢筘的金属丝格栅完成的。
4.
The warp occupies a certain width in the reed, and each pick of weft has this length as it is beaten- up.
经纱在钢筘上占据着一定的宽度,打纬完成后,每根纬纱占据着一定的织物长度。
5.
It is necessary to hold the fabric at the fell of the cloth to insure that the reed beats the filling across the width of the fabric as nearly parallel as possible.
应该在织口处对织物加以握持,以保证打纬时,钢筘在整个织物宽度上尽量保持平行。
6.
Air flow field in unconventional shaped reed and its influence on weft yarn flying
筘槽内引纬气流场分布及其对纬纱飞行的影响
7.
At the beginning of the weaving cycle, the reed is moved backward to allow for filling insertion.
在织造循环开始时,钢筘向机后运动,以便于引入纬纱。
8.
Beat - up, Warp and Fabric Control
打纬,经纱与织物的控制
9.
As the reed moves away from the fell, the cloth at the fell will contract width way under the influence of the tension in the weft produced by the effort of the warp to crimp it.
当钢筘从织口处后退时,由于经纱使纬纱屈曲而产生的纬纱张力会使织物在织口处沿宽度方向收缩。
10.
COMPUTER SIMULATION FOR THE INFLUENCE OF WEFT COMPRESSIBILITY ON WEAVING
计算机模拟纬纱的可压性对打纬的影响
11.
Design and Study of Beat-up Mechanism and Weft Insertion Mechanism of High-powered Rapier Looms;
高性能剑杆织机打纬和引纬机构的设计与研究
12.
This paper analyses the linkage beating-up mechanisms based on technical requirements of the bating-up movement for weaving.
依据织造工艺对打纬运动的要求分析了连杆打纬机构。
13.
steel reed for cotton and wool loom
钢筘(棉、毛织机用)
14.
Beat-up Mechanism of the Sulzer Projectile Loom
苏尔寿片梭织机的打纬机构
15.
Analysis on Mesoscale Characteristic of Rare Thunderstorm Snow Weather in Low Latitude Plateau
低纬高原罕见“雷打雪”中尺度特征分析
16.
A series of orifices, with slots to permit the removal of the filling at beat - up, can be placed along the filling axis.
在沿纬纱的飞行方向上,布置一系列的孔道,孔道上开有打纬时的脱纬槽。
17.
After the filling is inserted, by whatever means of insertion, it must be incorporated into the body of the fabric. This is the purpose of beat - up.
无论采用何种引纬方法,在纬纱引入之后,它必须与织物结合在一起,这就是打纬的目的。
18.
The usual mechanism which gives the reed its motion is known as the lay.
驱动钢筘运动的机件通常称为筘座。