1.
Brief Analysis on Heat Treatment Process of Main Spindle for F11250 Universal Dividing Head of 45 Steel
浅析45钢制F11250万能分度头主轴热处理工艺
2.
Research the Bearing Capacity of Universal-joint Spindle in 170 Piercing Mill Main Transmission System
170穿孔机主传动系统万向接轴承载能力分析
3.
"The driving shaft causes the spider to rotate, and the other two trunnions of the spider cause the driven shaft to rotate."
主动轴使万向节十字轴转动,另外两个万向节十字头使从动轴转动。
4.
The Analysis of Fracture for the Flat Head of Universed Joint
1150初轧机万向接轴扁头断裂分析
5.
"When the two shafts are at an angle to each other, the bearings in the yokes permit the yokes to swing around on the trunnions with each revolution."
当两轴相互处在同一角度上,主动轴转动时万向节叉上的轴承使万向节叉绕万向节十字轴摆动。
6.
The drive shaft is able to contract, expand, and change operating angles while transmitting torque through the use of universal joints and slip joints.
在万象头和伸缩接头的应用下，传动轴还能进行收缩，伸展或改变运行角度等方式来传递扭矩。
7.
"The four arms of the spider, known as trunnions, are assembled into bearings in the ends of the two shaft yokes."
万向节十字轴的四个轴颈叫做万向节十字头,分别装在两个万向节叉顶端的轴承中。
8.
Structural Strength Analysis of Constant Velocity Joints for Car Drive-shaft by Finite Element Method;
轿车驱动轴等速万向节结构强度的有限元分析
9.
Strength Analysis of Pressure and Torsion Combination Loads of Flapper Teeth of LTC
螺杆钻具瓣形万向轴瓣齿压扭组合强度分析
10.
high precision automatic microfeed universal boring head
高精度自动微进万能镗头
11.
Influence of oil temperature on lubricating performance for main bearing
机油温度对主轴颈轴承润滑性能的影响
12.
FEA of Joint Performances of 7:24 Tapered Tool-holder/Spindle on NC Machine
数控机床7:24锥度刀柄主轴连接性能的有限元分析
13.
Analysis of Static Strength and Stiffness for Spindle in High Speed Rotating Hydrostatic Bearing Union
高速旋转静压轴承接头芯轴的静强度和刚度分析
14.
Performance Analyse and Test of Rolling Bearing on the High-Speed Spindle;
高速主轴用滚动轴承性能分析与试验研究
15.
Study on the Static and Dynamic Characteristics Analysis and CAD of the High Speed Bearing-Spindle System;
高速轴承—主轴系统静动态性能分析及其CAD研究
16.
The Performance Analysis of Diesel Crankshaft and the Research for Calculation Method of Crankshaft Fatigue Strength;
柴油机曲轴性能分析及曲轴强度计算方法研究
17.
Intensity Analysis and Calculation of the Principle Shaft System Parts of Continuous Extrusion Machine;
连续挤压机主轴部件强度分析与计算
18.
The Probability Finit Element Analysis of Stiffness Dependability for Spindle of Machine Tool;
机床主轴刚度可靠性概率有限元分析