1.
One-Time Tensioning Formation Technology of Single Steel Strand Wire of Anchor Cable of Steel Cantilever Installed Truss Arch Bridge
钢桁架拱桥悬臂安装扣索单股一次张拉施工技术
2.
Installation of Tower Crane Used in Cantilever of CCTV Main Building
CCTV主楼悬臂部位大型塔式起重机安装技术
3.
These capacity charts show the figures when handling load off main boom head sheaves in a case of mounting fly jib on top of main boom.
这些功能表显示了在主悬臂顶端安装飞臂情况下将负载操作离开主悬臂头滑轮时的数据。
4.
cantilever walking crane
壁装移动式悬臂起重机
5.
Install bolts holding front of suspension crossmember to frame rails under upper control arm.
安装将悬吊横梁前部紧固到上控制臂下面的框架轨道的螺栓。
6.
Low the harnessed implement to a flat surface until the embedding legs touch it and the depth control wheels are in the air.
降低安装设备放置平面直到接触到掩埋臂,并且深度控制轮悬空。
7.
"There are three types of coil-spring front suspension. In one, the coil spring is located between the upper and lower control arms, and the lower control arm has one point of attachment to the car frame."
有三种螺旋弹簧前悬挂结构:一,螺旋弹簧安装在上、下控制臂之间,下控制臂的一端与车架相连;
8.
Study on Construction Control of Cantilever Erection Continuous Curved Girder Bridge;
悬臂拼装曲线连续梁桥施工控制研究
9.
Research on Safety Distance between Gas Pipeline and Foundation Ditch of Cantilever Piles
燃气管道与悬臂桩基坑安全间距研究
10.
To add rigidity, braces are sometimes fastened from the overarm to the knee.
为了增加刚性,有时从悬臂到升降台装上一对撑臂加以紧固。
11.
Study on Construction Technology of Box Girder Segment s Stub Matching Precast and Cantilever Erection;
箱梁短线匹配预制及悬臂拼装施工技术研究
12.
Study on Construction Geometry Control of Prefabrication Based on Short-Line Method and Cantilever Erection Continuous Girder Bridge;
短线预制悬臂拼装连续梁桥施工线形控制研究
13.
Comprehensive Application of Construction Techniques for Segmental Precasting and Cantilever Assembling to Bridge Works
节段预制、悬臂拼装工艺在工程中的综合运用
14.
Operation Safety Monitoring of Tower Crane Used in Cantilever of CCTV Main Building
CCTV主楼悬臂部位塔式起重机运行安全监测
15.
Install the push rods, rocker arms, pivots and bridges in the order they were remove
按照拆卸顺序安装推杆、摇臂、枢轴和桥臂。
16.
Modal analysis of frame of cantilever NC assembling machine for assembled camshaft
装配式凸轮轴悬臂式数控装配机的机架模态分析
17.
Install pitman shaft and side cover in the housing.
在机座中安装转向摇臂轴和侧盖。
18.
The arm with self-locking device, easy for adjusted, more safety.
设有托臂自锁装置,调整方便,使用安全.