1.
Wire Extension Adaptability Digital Fuzzy Control System for CO_2 Short-circuit Welding
短路过渡焊丝伸出长度适应性数字模糊控制系统
2.
They are generally produced with the tenacity of 2-3.5 grams per denier and elongation of 25% ～40%.
长丝的强度一般为2～3.5克;旦尼尔,伸长率为25%～40%。
3.
The process of drawing irreversibly stretches the spun filaments and winds up the stretched yarn. The strength and recoverable extensibility are thereby increased.
在牵伸过程中连续拉伸长丝,并将其卷绕起来,长丝的强度和弹性会因此而提高。
4.
A wire lengthens while it is heated
金属丝受热则伸长。
5.
Indicates a fillet weld. Increase height extension line will appear.
表示角焊。“增加高度并延长”线将出现。
6.
The mercerization process causes the cotton fibers to swell laterally and shrink longitudinally.
丝光过程使棉纤维沿直径方向膨胀,沿长度方向伸长,
7.
extend or stretch out to a greater or the full length.
伸展或伸出更大或更长。
8.
Used for testing indexes of polyurethane monofilament, such as breaking tenacity, elongation at break, load at specified elongation, relaxation of stress, plastic deformation, etc.
用于测定氨纶丝断裂强度、裂伸长率、伸长负荷、力松驰、性变形等性能指标。
9.
The fungus primarily grows along tree roots via hyphae, fine filaments that mat together and excrete digestive enzymes.
一般说来，真菌会沿着树根生长，伸出菌丝并分泌很多消化酶。
10.
Regression and Analysis on Metal Strength of Welding Seam of Welding Core Wine
药芯焊丝焊缝金属强度的回归与分析
11.
Correlation is negative at the0.05 level with Filament size and Skein ratio.
含胶率和伸长率与茧丝纤度在0．5的水平上具有的负相关性。
12.
To measure strength breaking elongation of various kinds of farics such as cotton, wool,twine.silk and chemical fiber etc.
用于测定棉、毛、麻、丝及化纤等织物的抗拉断裂强度及断裂伸长。
13.
Used for testing breaking tenacity and elongation at break of raw silk in skein and bobbin.
用于测定绞装和筒装生丝的断裂强度及断裂伸长率。
14.
"Spinning is the process of drawing out and twisting a mass of cleaned, prepared fibres. Filament yarns generally require less twist than do staple yarns."
纺纱是对纤维集合体牵伸加捻的过程。长丝比短纤维需要的捻度少。
15.
Most stretch yarns can be extended from one and one-half to twice their normal or relaxed length.
大多数弹力丝可被拉伸到正常或松驰状态长度的1倍半到2倍。
16.
To reach or extend over or beyond.
伸出在…之上因伸展过长而超出
17.
Unique output special design can suit wire filling welding and form good-looking welding seam.
独特的输出特性设计更适合填丝焊接，焊缝美观。
18.
Before all the acetone has evaporated, the still-plastic filament is stretched slightly to align the long molecules and develop the inherent strength.
在丙酮被完全蒸发掉之前,依然呈塑性的长丝被轻轻地拉伸,目的是使长分子顺直,增加固有强度。