1.
This method is a combination of pickling and blast cleaning.
这一方法是酸浸除锈法和喷砂除锈法的组合。
2.
Remove rust, mill-scale and other loose material by abrasive blasting or power tool cleaning.
用喷砂或其他电动工具除去铁锈、氧化皮等。
3.
Use a blast cleaner or power tool to remove weld flux slag, weld metal spatters, weld flux fume deposits, rust and damaged paint film in welded areas.
通过喷砂或电动工具除去焊渣、飞溅焊烟、锈迹和焊接部损坏的漆膜。
4.
Blast cleaning of all except tightly adhering residues of mill scale, rust and coatings, exposing numerous evenly distributed flecks of underlying metal.
喷砂除去所有附着的氧化皮、锈迹和漆膜，除了牢固附着的。露出大多数的有锈斑点的钢板。
5.
Bed frame welded by profile steel are stable and reliable.The surface treated with advanced electrostatic plastic-spray is anti-aging and ante-rust.
床体采用型钢焊接而成，牢固可靠，表面除锈，静电喷涂，抗老化，不生锈。
6.
All traces of rust should be removed from the metal before you begin to apply paint.
在你开始喷漆之前，要把所有的锈迹都从金属上除掉。
7.
The impact of architecture steel structure surface which is caused by blasting process--Summary about the surface disposure of the decorative rusty-plate which is used by the CCTV New Site Building
喷砂(抛丸)工艺对建筑钢结构表面的影响——央视新址大楼装饰锈钢板表面处理总结
8.
Sand and rusts removing of large-sized cast iron,cast steel,steel structures,large-sized forging and surface freatment of oxidized workpieces.
大型铸铁、铸钢件，钢结构件、大型锻件，热处理件的清砂、除锈去除氧化皮表面清理等。
9.
The stainless sand-remover can remove the sand &metal particles with an efficiency of 96% above.
不锈钢除砂器能使淀粉乳中的残留细泥沙与金属粒等杂质除去，效率可达96%以上。
10.
The suggestion includes:1) use corrosion-resistant coating material as surface protection and2) use sprinkle rust-removing technique and mechanical spray coating process in internal anti-corrosion construction.
建议:①用耐腐蚀的涂料作表面涂层保护;②油罐内防腐施工中采用喷淋除锈和机械喷涂工艺。
11.
jet-projecting machine, sand, steam, powder or liquid (excl. container cleaning machines, soot remover for boilers, and jet type dental drills)
砂、蒸气、粉末或液体喷射机（不包括容器清洗机器、锅炉除烟垢器及喷射式牙钻
12.
This preparation consists of sanding away any paint or rust to obtain a smooth but not highly polished surface.
准备工作包括用砂纸打磨，除去油漆和锈迹，以使表面光滑但又不抛得很光。
13.
Clean water,oil,rust,dust and other filths before spraying the paint on the surface.
喷涂前应先把被涂物表面之水份、油脂、铁锈、灰尘及附着污物清除干净。
14.
open-pressure blasting
露天压风喷砂清理法
15.
forming machine for making foundry moulds of sand (excl. sand-jet sprayers)
铸造用砂模成形机（不包括喷砂装置）
16.
Application of gunite pile technique to layer of coarse and gravelly sand
喷浆桩技术在粗砂砾砂地层中的应用
17.
The surface must be tough, clean, dry and free from oil, grease, wax and other dirt. Use sanblasting, whetting or acid-wash to remove the floating cement paste.
底材必须坚固、清洁和干燥，无油、脂、腊和其他污物。去除浮浆（可用喷砂、研磨、酸洗）.
18.
Technology study on cast iron parts' repair with grit-blasting and Arc-spraying;
铸铁零件喷砂电弧喷涂修复工艺研究