1.
Research and Design of Online Temperature-Monitoring of Aluminium Cell Shell and Diagnosis of Cell Status System;
铝电解槽槽壳温度在线检测及槽况诊断系统的研究与设计
2.
Research & realization of aluminium reduction control based on cell working condition analysis
基于工况槽况的电解生产控制研究及实现
3.
Research and Application on the On-line Temperature Detection of Aluminum Cell Shell and the Cell Status Diagnosis Expert System;
铝电解槽糟壳温度在线检测与槽况诊断专家系统的研究与应用
4.
The Research of Data Mining Technology in Trend Control of the Aluminum Electrolyte Pot Condition;
数据挖掘在铝电解槽槽况趋势控制中的研究与应用
5.
INSPECT TERMINAL (CAV 16) FOR SPREAD OR DAMAGED CONDITION.
由于扩展或损坏的状况检查端子（槽16）。
6.
Measurement of Harmful Gas and Performance Analysis of Tin Bath
锡槽内有害气体含量的测定及工况分析
7.
The other 12 patients (224 teeth) were carried out with light-cure veneer bonding technique.
在托槽粘结后的四周、八周、十二周分别记录两组患者的托槽脱落率的情况。
8.
(4) The condition under which steel rollers fail to take up the ink on offset presses, and instead are wet by the fountain solution.
(4)在柯式印刷机上，钢锟不带墨，反而被水槽液湿润的情况。
9.
The dashed lines on the rotors show the locations of the recesses and how deep they are.
转子上面的虚线就示出了凹槽的局部位置及其深度情况。
10.
and the cost of ionic membrane caustic soda were decreased with the electrolyzer.
运行情况表明此种电解槽可降低离子膜碱的生产成本。
11.
Periodontitis of the population in neolithic age from banpo museum;
半坡博物馆馆藏六千年前人牙槽骨水平状况分析
12.
The observation of the level of crestal bone around submerged and non-submerged implant during healing period
愈合期埋植型和非埋植型种植体周围牙槽骨吸收情况观察
13.
starting sheet cells
始极槽,种板槽,始板槽
14.
groove-cutting chisel
槽刨, 油槽铲(轴承)
15.
Gluey material added to paper to create a smooth writing surface and to make it less sensitive to ink. See Engine sizing. Surfacesizing and ATS.
造纸时，把粘性的物料加入纸内，使纸张表面平滑的情况。参阅机内施胶，表面施胶和槽法施胶。
16.
The housing condition for blacks in Birmingham was bad and there were few jobs for blacks. Only 25% of them could vote.
伯明翰黑人的住房情况很槽，那里黑人的工作机会也少之又少。只有25%的黑人有选举权。
17.
Blending of the vats 1 month before bottling. Earth filtration and fining if necessary.
装瓶前一个月才将不同酒槽的酒液依年份状态混和，视酒体状况决定是否过滤凝清。
18.
Surface sizing: Applying a thin coating of size on the surface of paper on the sizing press of the papermaking machine.
表面施胶:在造纸机上的施胶部，纸面涂上薄胶层的情况。参阅机内施胶，施胶，槽法施胶。