1.
The Process Control for the Gas Bubble Defect of the H08E Continuous Casting Billets
H08E连铸方坯的气泡缺陷的控制
2.
Process Measures for Resolving the Skin Blowhole of Q195 Drawing Quality Billet
解决Q195拉丝用方坯钢气泡缺陷的工艺措施
3.
The Analysis of Defects on the Surface Lacunas and Air Bubble of Hfe62-1 Cylindrical Pressure Parts
四六铁黄铜筒形件热反挤压表面重皮与气泡缺陷的分析
4.
Surface must be smooth , No copper stain 、 shrinkage、flow mark 、 bubble etc .
表面光洁、色泽均匀，无缩瘪、流痕、气泡等缺陷。
5.
The effect of hydrogen on the ductility of electroless copper deposit is primarily caused by molecular hydrogen contained in voids, particularly the typeⅢ GB voids.
镀层延展性降低的主要原因是由氢气泡的缺陷效应，特别是第三类氢气泡、粒边界气泡空穴。
6.
Influence of Gas Void and Gas Crack Defects on Electrical Tree Initiation in Silicone Rubber
气泡及气隙裂纹缺陷对硅橡胶电树枝起始特性的影响
7.
"antique" cast glass (i.e., containing air bubbles or other deliberate defects), non-wired in sheets
“老式”大片压铸玻璃（即含有气泡或其他有意的缺陷）,无金属线,未加工
8.
Preparation and Analysis on the Defects of Aluminum foams via Melt-foaming method
熔体发泡法制备泡沫铝合金及其缺陷分析
9.
Testing Study on the Defects of Polyurethane Foam Molding of Automobile Seat
汽车座椅泡沫聚氨酯发泡成型缺陷试验研究
10.
The dispelling ways of forming barbotage in the surface of the reinforced steel bar
热轧带肋钢筋表面起泡缺陷解决方案
11.
Design Defects and Improvement of EPB Shield TBM Foam System
EPB盾构泡沫系统设计缺陷与改进
12.
Common Defects of Styrofoam Patterns for EPC Process and Prevention Methods
消失模铸造用发泡模常见的缺陷及防止方法
13.
Effect of cell wall deficiency on vancuolating pathogenicity of helicobater pylori
细胞壁缺陷对幽门螺杆菌空泡毒性作用的影响
14.
They also look for potential molding defects, such as gas entrapment, weld lines, shorts and sinks.
也可以看出潜在的模塑缺陷如气体夹陷、熔接线、缺胶和凹陷等。
15.
The lack of air in the bulb prevents the filament from burning up.
灯泡内缺乏空气就使灯丝不致烧掉。
16.
Air pollution, birth defects linked
出生缺陷与空气污染有关
17.
Research on the Casting Shrinks Properties and Air Hole of Ti-43Al-9V Intermetallic Compounds;
Ti-43Al-9V铸造受阻收缩及气孔缺陷
18.
Formation Reason and Countermeasures of Blowhole Defects for Cylinder Block Casting
柴油机缸体气孔缺陷成因分析及对策