说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 固定球阀
1.
The metal hard seal fixed on the ball valve divides into the normal temperature and the high temperature, when the application temperature is higher than180℃, please indicate the application temperature the first.
金属硬密封固定球阀分为常温型和高温型,当使用温度大于180℃,订货时应注明使用温度。
2.
Lift out the disc holder assembly from the body of the valve.
从阀门的阀体内提起阀瓣固定器总成。
3.
To reverse the seat disc, unscrew the disc screw and disassemble the disc washer and disc rubber from the disc holder assembly.
为了翻转阀座阀瓣,则要拧松阀瓣螺丝,从阀瓣固定器总成拆解阀瓣垫圈和阀瓣橡胶。
4.
The use of seat screws as a retention method is prohibited.
禁止采用阀座螺丝作为固定阀座的方法。
5.
Outer row of studs secures the yoke to the body.
双头螺栓的外部排列将阀架固定在阀体上。
6.
In all designs, the valve stem normally serves as a piston rod with disc fastened directly to them.
在所有结构中,阀杆通常作为活塞杆,阀瓣直接固定在阀杆上。
7.
Throttle Body Mounting Bolts—Engines—Typical
节气阀体固定螺栓—引擎—典型的
8.
Throttle Position Sensor Mounting Screws
节气阀位置感知器固定螺丝
9.
Solenoid Switch Valve Latched in TCC Position
电磁螺线管开关阀门固定在TCC位置
10.
Anchor/support bolt holes are located in base of body.
固定器/支架螺栓孔位于阀门的基座。
11.
Type of valve- gate, globe, check, etc.
阀门种类:闸阀,截止阀,止回阀,蝶阀,球阀,等等。
12.
The relief valve cover shall be secured with stainless steel bolts and shall utilize a quarter-turn locking joint to capture the spring load of the relief valve.
安全阀阀盖应该采用不锈钢螺栓紧固,应该采用四分之一转锁定连接来所定安全阀的弹簧负载。
13.
The valve cover shall be held in place through the use of a single grooved style two-bolt coupling.
阀盖应该通过单个沟槽状双螺栓联结器固定住。
14.
The PCV valve sticks in the open, maximum-flow position.
把PCV阀固定在开启位置即最大流量位置。
15.
We need an eye bolt to fit this valve.
我们需要一个有眼螺栓来固定这个阀门。
16.
Experimental and Numerical Study of Flow Field on Folded-Downward Edge Fixed Valve Tray;
折边固定阀塔板流场的实验研究和数值模拟
17.
Experimental Study and Numerical Simulation of Hydrodynamics Performance for Gas Passing Through the Fixed-Valve;
气体穿过固定阀的流体力学性能及数值模拟
18.
The designing of 6.0MPa electric actuator cylinder head valve for CO_2 fixed extinguishing system
CO_2固定式灭火系统6.0MPa电动气瓶阀的设计