1.
Study on Semisolid Feedstock of A356 by Controlled Pouring Methods;
控制浇注方法制备A356半固态坯料的研究
2.
The molten metal may enter the ingot mould in two ways: from the top and from the bottom. Top pouring is the simplest and cheapest method, but gives poor control over the rate of pouring.
钢液注入钢锭模可采用两种方式:上注和下注。上注法最简单，成本最低，但不好控制浇注速度。
3.
Discussion of Plan for Massive Concrete Placing of Pump Gate Floor
泵闸底板大体积混凝土浇注方案讨论
4.
Adeline steelmaking process
阿德莱熔模铝热离心浇注法
5.
Preparation of Mg-Ni-Si Metallic Glass by Vibration Casting Process;
震动浇注法制备Mg-Ni-Si金属玻璃
6.
Design methods of two representative runner- the fan gate and tapperd runner, were analyzed.
分析了两种典型的横浇道——扇型浇道和切线型浇道的设计方法。
7.
Top pouring is the simplest and cheapest method, but gives poor control over the rate of pouring.
上注法最简单，成本最低，但不好控制浇注速度。
8.
another method is to pour the entire thickness of concrete and then force the steel mesh down into it to a predetermined level.
另一种方法是将混凝土浇注到足够的厚度，然后将钢筋网压入到其中预先确定的深度。
9.
Yorkshire pudding is cooked by pouring batter into a greased baking tin, and baking at a very high heat until it has risen.
约克郡布丁的制作方法是将面糊浇注在涂过油的烘培罐里，然后在高温下烘烤加热至其膨胀。
10.
In this paper, the technology of ramming ceramic mould using loose mixture with aluminium phosphats colloid as binder was researched, and pouring experiment was also made.
研究了以磷酸铝为粘结剂配制松散料，捣制陶瓷铸型的工艺方法，并进行了浇注试验。
11.
Study on Non-destructive Testing and Digitization Image-display Method Using Fast Neutron for Cavity Defects in Interfaces between Steel Plate and Pour Concrete;
钢板与浇注砼结合面脱空缺陷中子无损探测及结果数字显像方法研究
12.
"In the anhydrite zone,given a 3 m thick Base, 5m3 of concrete is installed in the Base and 4 m3."
在硬石区,3米厚的基底浇注混凝土5立方米,拱穹浇注混凝土4立方米。
13.
The setting scheme of late poured band and attention problems in design and construction
后浇带的设置方案及设计施工中应注意的问题
14.
The influence of cast mold in rebound testing of concrete compressive strensth
浇注模板对回弹法检测混凝土抗压强度的影响
15.
The Application of Image Recognition Method Based on Hu-moment Invariants in Auto-pouring System
Hu不变矩识别算法在自动浇注系统中的应用
16.
Design of Gating System of Planetary Castings Using Proportional SoIidification Modulus Calculation Method
运用均衡凝固模数法设计行星架浇注系统
17.
Preparation of semi-solid feedstock by serpentine pipe pouring
采用蛇形管通道浇注法制备半固态浆料
18.
testing method for grain size of castable refractories
可浇灌耐火材料粒度试验方法