1.
Sub-millimeter Tests of the Newtonian Gravitational Inverse-Square Law;
亚毫米尺度下牛顿反平方定律的检验
2.
Investigation of Metal-Caldding Optical Waveguide with Submillimeter Scale and Its Application;
亚毫米尺度金属包覆波导的特性和应用研究
3.
Propagation Loss and Application Research in Symmetrical Metal-Cladding Optical Waveguide with Sub-Millimeter Scale
亚毫米尺度对称金属包覆波导损耗特性的研究及应用
4.
doorway dimension
门开尺寸(ISO规定最小宽度为2200毫米
5.
Controlling measurements shown in parenthesis are in millimeters.
以括号中以毫米为单位的尺寸为准
6.
The size of each assembling sleevepiece produces as above is φ200×270mm, the total length of the assembled lance is about 2400mm.
每节组件尺寸为Φ200×270毫米,组装喷枪总长为2400毫米。
7.
In strength property experiment, the sample size is 150×15×5mm.
在强度实验中试件尺寸采用150×15×5毫米。
8.
CNC Hydraulic Press Brake offers" Conic Bending" up to a maximum of15 mm along the whole length.
电脑数控液压式折弯机提供"锥形折弯"全长尺寸最大可达到15毫米。
9.
The dimension of a seagull df - 1 is 146*99*96mm, with a standard lens and it weigh 960 gram.
带在标准镜头的海鸥ＤＦ－1的外形尺寸为146×99×96毫米，重量为960克。
10.
It can burn holes in a steel plate 0.125mm thick at a distance of several feet.
在几英尺以外它就能把0．125毫米厚的钢板烧出洞来。
11.
Invalid input. Please enter a dimensional value with a measurement unit such as '8 in' or '10 mm'.
输入无效。请输入一个带有度量单位的尺寸值，如“8 英寸”或“10 毫米”。
12.
Invalid input. Please enter a positive dimensional value with a measurement unit such as '8 in' or '10 mm'.
输入无效。 请输入一个带有度量单位的正尺寸值，如“8 英寸”或“10 毫米”。
13.
When the little sixteen-millimetre film is blown up to standard size, the image often blurs.
把十六毫米的微型胶卷放大到标准尺寸，图象常会模糊。
14.
Locomotive and car clearance boundary and structure clearance boundary for 762mm gauge railways--Classification and basic dimensions
GB188-1963762毫米轨距铁路机车车辆限界和建筑接近限界分类及基本尺寸
15.
If a bay is inclined to the general line of the base at an angle of 10 mm in 24m, the error will be 0.1 ppm.
如果一个尺段偏离基线总方向的角度相应于24米距离上的10毫米，则误差为0．1×10-6。
16.
millimetre of mercury
毫米水银柱(mmHg)
17.
Bleed: Area of colours or photographs that extend beyond the cut edge of a page. The bleed allowance beyond the trimmed size is usually 3 mm or 1/8 inch.
出界:相贬或底色范围伸出页边裁切线以外者。出界宽限通常是完成尺寸加3毫米或1/8时。
18.
1 plan in three sides; front, side and ground, with the specification of its materials and size in mm(millimeter).
一张三视图;正视,侧视及上视,附上材质及尺寸（单位为毫米）的设计说明书.