1.
A pole connecting the rear axle of a vehicle with the front.
连接杆连接车辆前后轴的杆
2.
Vehicle Axles Disturbing Forces Estimation Based on Adaptive Kalman Filter
基于自适应卡尔曼滤波的汽车前后轴干扰力估计
3.
Wheel base( front-mid/mid-rear)
轴距(前-中/中-后)
4.
Measuring deflection of crank shaft of M.E. before starting up(after sea trial).
主机动车前（航行试验后）曲轴甩档测量。
5.
Research and application of axons regeneration after injury of dorsal roots
脊神经后根轴突再生研究及应用前景
6.
Drive shafts modified for new location on the axle housing and because of the new doubler. Double joint added to the front drive shaft and the shaft made longer. Rear drive shaft shortened.
传动轴修改来配合分动箱放大齿轮组。改装内容包括双十字轴和加长前传动轴。后传动轴截短。
7.
Radius arms, cross members, radius arm brackets and cross member brackets rebuilt or modified for new axle locations.
根据新的前后桥的位置，对半轴，十字轴及相关支架进行改造。
8.
When swinging transmission machine operation, the force constant rotation axis to make efforts before and axial rotation move backward.
当摇摆传动机械运行时，等速旋转入力轴使出力轴向前和向后旋动。
9.
The Front/Reverse switching mechanism was placed on the driving shaft, while the acceleration clutch was placed on the driven shaft.
前/后机械开关安装在驱动轴上，同时加速离合器安装在从动轴上。
10.
Permanently sealed and lubricated ball bearings front and rear.
前后端盖装有永久密封和自润滑的滚珠轴承。
11.
Check the deflection of the crankshaft both before and after repair.
在修理前和修理后都要检查曲轴的变形情况。
12.
Experimental Study on the Multiaxial Mechanical Behavior of Plain High-strength Concrete before and after High Temperatures;
高温前后高强混凝土多轴力学性能试验研究
13.
They permit the friction disk to slide Back and forth along the shaft But force the disk and the shaft to rotate together.
可以使摩擦盘沿着主轴向后或向前滑动,又可使圆盘和主轴同时转动。
14.
When swinging drive mechanical operation, such as the rotation speed of the force to make efforts axial shaft before and backward rotation and enable higher plane.
当摇摆传动机械运作时，等速度的旋转入力轴使出力轴向前和向后旋转，并使平面升高。
15.
A hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion.
掣爪，棘爪一种枢轴或转轴器械，能与齿轮缺口或齿间吻合来前进或防止后移
16.
And the wide track, long wheelbase, low centre of gravity and 50:50 weight distribution ensure perfect balance at all times.
宽轮距、长轴距、低重心和前后50:50的重量分配构成了完美平衡。
17.
Cams are fastened on the fixture by screws, and the inside transmission system rotates cams to puch crank arms to change the position of slides.
凸轮固定在旋轮轴上，可以螺丝调整前后，并用以推动滑座之运动。
18.
The distance from the center of the front wheel to that of the rear wheel in a motor vehicle, usually expressed in inches.
轴距机动车中从前轮中心到后轮中心间的距离，常用英寸表示