1.
Process Technology Research on Valve Seat Ring and Valve Stem Guide Hole of Cylinder Head;
气缸盖气门座圈和导管孔的加工工艺研究
2.
The Research about Several Fine Processing Technologies of Valve Seat Ring and Valve Stem Guide Hole of Cylinder Head;
气缸盖气门座圈和导管孔的几种精加工工艺分析
3.
A spring on the valve stem tends to hold the valve on its seat (closed). The lower end of the spring rests against the cylinder head.
气门杆上的弹簧使气门保持在气门座上(关闭状态)。弹簧的下端抵在气缸盖上。
4.
"In the other kind of valve mechanism for an engine, the valves are located in the cylinder Block instead of the head."
另一种气门机构的气门是装在气缸体上,而不是装在气缸盖上。
5.
Spark plug M10X1 with flat seating and cylinder head housing
GB/T6784-1986M10×1平座火花塞及其气缸盖安装孔
6.
The Control of Cylinder Cover Spring Holder Hole Cutting tool and Sinks the Hole Depth Size
气缸盖弹簧座孔刀具与沉孔深度尺寸的控制
7.
The Study on Design of Four-Valve Intake Port in 4V105 Diesel Engine;
4V105柴油机四气门缸盖进气道的设计研究
8.
"Spark-plug holes are provided, along with pockets into which the valves can move as they open."
气缸盖上留有火花塞口和凹槽,凹槽使气门打开时可以移动。
9.
The cylinder head carries the valves, valve springs and the rockers on the rocker shaft, this part of the valve gear being worked by the push-rods.
气缸盖携带阀门，气门弹簧和在摇臂杆上的摇臂，这部分的气门传动机构通过推杆工作。
10.
Sometimes the camshaft is fitted directly into the cylinder head and operates on the valves without rockers.
有时，凸轮轴直接安装在气缸盖上并且不用摇臂控制阀门工作。
11.
Explore on the Influence of the Race Sealing Taper Quality in Different Technological Parameter under the Condition of Pre-production Low-volume
小批试制条件下加工工艺对缸盖气门密封带质量影响的研究
12.
The Analyse of Cylinder Head Valve Pipe Hole and Sealing Trip on Their Technical Method Used in the Machining Center
缸盖气门导管孔和密封带在加工中心上的工艺分析
13.
Like the cylinder block, the head is made from either cast iron or aluminum alloy.
像气缸体一样，气缸盖是由铸铁或者铝合金制成。
14.
The cylinder head is attached to the block with high-tensile steel studs.
气缸盖与气缸体用高强度的钢螺栓缚连结。
15.
Valve Tappet Adjustment For Three And Five--Cylinder Engines
三缸与五缸内燃机气门间隙调整方法
16.
The Numerical Simulation of Flow and Temperature Field in Cylinder Head of Diesel Engine with Small Cylinder Bore;
小缸径柴油机气缸盖流场、温度场的数值模拟
17.
Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.
安装汽缸盖，进气歧管和排气管，请参阅本部分的汽缸盖安装。
18.
having both inlet and exhaust valves located in the cylinder head.
在气缸盖上有出口和入口。