说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 句库 -> 密封垫片
1.
Research on the New Fluoroelastomer Coat-Metal Gasket for Seal of Internal-combustion Engine;
内燃机用新型氟橡胶涂层金属密封垫片的研究
2.
This plant is specially engaged in research, development and manufacture of the special equipment for static sealing spacer.
本厂是从事静密封垫片专用设备研究开发、造的专业厂家。
3.
Add sealed shim between the two flanges and then lock down the bolt.
安装时两法兰间需加密封垫片,然后均匀拧紧螺栓。
4.
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
本阀可水平或垂直安装,安装时两法兰连接中间必须加密封垫片,然后均匀锁紧螺栓。
5.
Pay attention to the flow direction of medium marked on the body. Add the sealed shim between the two flanges and then screw down the bolt.
安装时请注意闸门本体上标明介质流向。两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
6.
Development of computer check and control system for a test device for comprehensive property of seal gaskets Ⅱ.Software design of computer check and control system.
密封垫片综合性能试验装置微机检测控制系统的研制 Ⅱ?微机检测控制系统软件设计
7.
joint gasket- or packing- type, of metal sheeting combined with other material (e.g. asbestos, felt, paperboard)
金属片与其他材料(例如,石棉、毡、纸板)的静密封或填密封式接合衬垫
8.
Spiral wound gaskets test method of hydraulic pressure sealing characteristics
GB/T4620-1984缠绕式垫片水压密封性能试验方法
9.
Spiral wound gaskets test method of steam sealing characteristics
GB/T4621-1984缠绕式垫片蒸汽密封性能试验方法
10.
Test method for sealing characteristics of gaskets for pipe flanges
GB/T12385-1990管法兰用垫片密封性能试验方法
11.
joint gasket- or packing- type, of laminated metal foil
层压金属箔密封或填密封式接合衬垫
12.
gasket of metal sheeting combined with other material (e.g. asbestos, felt, paperboard)
金属片与其他材料(例如石棉、毡、纸板)制成的密封垫
13.
Rational Determination of Elastic Gasket Contact Stress and Closure Pressure for Shield Tunnel Segments
隧道管片密封垫接触应力和闭合压力的合理确定
14.
master cylinder outlet fitting gasket
主缸出油接头垫密片
15.
shock absorber relief valve gasket
减震器保险阀垫密片
16.
shock absorber filler plug gasket
减震器注油塞垫密片
17.
All sponge rubber packing for watertight doors need to be renewed.
所有水密门的多孔橡皮密封垫换新。
18.
Clean the injector port, replace critical injection port seals, replace injection port liners, and change septa as needed.
清洗进样口,如有必要,更换密封垫,衬管,隔垫。