1.
The product location you specified does not contain a recognized architecture type.
![点击朗读](/dictall/images/read.gif)
指定的产品位置不包含可识别的结构类型。
2.
The product location you specified is not a recognized architecture type.
![点击朗读](/dictall/images/read.gif)
指定的产品位置不是可识别的结构类型。
3.
The location you specified does not contain a recognized retail product.
![点击朗读](/dictall/images/read.gif)
指定的位置没有可识别的零售产品。
4.
The Effect of Positional Uncertainty in GIS Products Maked Decision
![点击朗读](/dictall/images/read.gif)
位置不确定性在GIS产品决策中的影响
5.
This position is too small and will make the steel material here too thin, can we widen it here?
产品的这个位置太小,导致模具钢料太溥,能够加宽这个位置吗?
6.
This package is suitable for tea, chocolates, biscuits and similar light food products.
![点击朗读](/dictall/images/read.gif)
创新,独特的直立产品便于在摆设位置中突出。
7.
We will make the lifter and (inner) slider in this position, will that be a problem?
![点击朗读](/dictall/images/read.gif)
产品里面的这个位置我们打算做斜顶或内行位,有问题吗?
8.
Steel and steel products--Location and preparation of test pieces for mechanical testing
![点击朗读](/dictall/images/read.gif)
GB/T2975-1998钢及钢产品力学性能试验取样位置及试样制备
9.
if it's a top-selling product, it may go in the best location in your warehouse or distribution center.
如果它是畅销产品,它就可能放到仓库或批发中心的最佳位置。
10.
The Modular Product Planning of Edge Position Control System Based on the Modular Matrix;
![点击朗读](/dictall/images/read.gif)
基于模块矩阵的边缘位置控制系统的模块化产品规划
11.
The Research of Product Structure and Product Configuration in Product Data Management System;
PDM中产品结构与产品配置的研究
12.
When a cylinder with this valve configuration is in the upright position, the inlet of the tube is immersed in liquid and the liquid phase will be removed.
当带有这种阀门配置的钢瓶处在垂直位置时,管子的入口浸在液体中,就可以提取液相产品。
13.
Research on Constraint Based Product Configuration Method and Product Configuration Optimization;
基于约束的产品配置方法和产品优化配置研究
14.
The position, direction, or way in which something, such as an automatic control, is set.
![点击朗读](/dictall/images/read.gif)
位置物品(如自控装置中)被装置的位置、方向或方式
15.
A. Position the bores according to the product. Drill φ 6 bores respectively with impact driller, after the center line for bolt bore is drawn in the appropriate position on the wall.
根据产品安装孔位,在墙面相应位置画出螺钉孔中心线后,用冲击钻分别钻φ6孔。
16.
Can we add ejector sleeves or ejector pins in the boss of this part?
![点击朗读](/dictall/images/read.gif)
产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗?
17.
1 electrical work external to the Product.
![点击朗读](/dictall/images/read.gif)
任何连接到本产品的外置电子装置。
18.
We will construct quality and taste and dedicate our products and services for customers.
![点击朗读](/dictall/images/read.gif)
我们营造品质与品位,奉献产品与服务。