1.
Remove bolts holding front of suspension crossmember to frame rails under upper control arms.
卸下将悬吊横梁前部紧固到上控制臂下面的框架轨道的螺栓。
2.
Install bolts holding front of suspension crossmember to frame rails under upper control arm.
安装将悬吊横梁前部紧固到上控制臂下面的框架轨道的螺栓。
3.
"In the second type, the coil spring is located between the upper and lower control arms, and the lower control arm has two points of attachment to the car frame. "
二,螺旋弹簧安装在上、下控制臂之间,下控制臂有两处与车架相连。
4.
Simulation Research of Robust Control System for Robotic Assisted Upper Extremity Based on MATLAB
基于MATLAB上肢康复机械臂鲁棒控制研究
5.
Simulation of resolved motion rate control arithmetic of mobile 3D manipulator
速度分解控制算法在移动三维机械臂上的仿真
6.
The upper limb were fixed with elbow at90° of flexion in order to observe the effects of angulation deformities upon the forearm rotation function.
结果斜索和骨间膜的上部纤维控制前臂的过度旋前，骨间膜的中下部纤维控制前臂的过度旋后。
7.
"There are three types of coil-spring front suspension. In one, the coil spring is located between the upper and lower control arms, and the lower control arm has one point of attachment to the car frame."
有三种螺旋弹簧前悬挂结构:一,螺旋弹簧安装在上、下控制臂之间,下控制臂的一端与车架相连;
8.
negative cam-controlled dobby
消极式凸轮控制多臂机
9.
"The steering knuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame.
转向节通过球头节与安装在车架上的上下控制臂相连。
10.
Such as the steering idler and the upper and lower control arms; removal and replacement of springs; removal and replacement of wheel hub and drum; and so on.
如转向转轴和上下控制臂,拆卸和更换轮彀和制动鼓等。
11.
An American woman has become the first in the world to receive a bionic arm that allows her to move the limb by the power of thought.
目前，一名美国妇女成为世界上首位拥有仿生手臂的人。仿生手臂的运动受人的思想的控制。
12.
dobby:a mechanical part in a loom that controls the harnesses so as to permit weaving of small geometric figures.
多臂机:织机上控制绳线以织出小的几何图案的机械部件.
13.
A mechanical part in a loom that controls the harnesses so as to permit weaving of small geometric figures.
多臂机织机上控制绳线以织出小的几何图案的机械部件
14.
Sometimes the camshaft is fitted directly into the cylinder head and operates on the valves without rockers.
有时，凸轮轴直接安装在气缸盖上并且不用摇臂控制阀门工作。
15.
The fast-idle cam position is controlled by an arm on the choke shaft.
快怠速凸轮的位置是由阻风门轴上的杆臂控制的。
16.
Integrated Structure Control Design Offlexible Arm System;
结构和控制系统综合最优设计及在柔性臂上的应用
17.
Fuzzy PID Control Application in Manipulator Controller
模糊PID控制在机械臂控制器中的应用
18.
Nonholonomic Motion Planning and Control of One-arm and Dual-arm Space Robot Systems;
单臂及双臂空间机器人非完整运动规划与控制