1.
On the Design of Control System of STM-750 Digital Spring Coil Grinding Machine;
STM-750数控弹簧端面磨床控制系统设计
2.
spring eye bolt
(弹簧的)环端螺栓，弹簧眼螺丝
3.
Replace spring tip inserts.
更换弹簧顶端插头。
4.
The end coil of the spring must be closed and flat.
弹簧两端的线圈/簧的端线圈应是闭合且平整的.
5.
On Design of Spring in Venturi Terminal Variable Air Valve
文丘里型末端变风量阀弹簧设计探讨
6.
"The upper end rests against a flat washer, or spring retainer, which is attached to the valve stem by a retainer lock (also called a keeper)."
上端抵在弹簧座上,在弹簧座的下面用栓销(或叫做定位销)加以定位。
7.
Install rear of spring onto rear spring shacklInstall shackle platDo not tighten.
安装弹簧后端至后弹簧钩环。安装钩环板。不要旋紧。
8.
When he pressed the springy button on top of the pen, he rose up into the air.
当他按下顶端的弹簧按钮时，他升到了空中。
9.
A spring holds the other ends in contact with the piston of a hydraulic cylinder.
另一端由一个弹簧托住，与液压缸的活塞相接。
10.
It is of built-in type, single seal face, single spring and rubber-bellows mechanical seal.
内装式、单端面、单弹簧、橡胶波纹管机械密封。
11.
Mechanical Behavior Analysis and Optimization of Hydraulic Unit Springs in Water Injection Pump
注水泵液力端弹簧力学行为分析与优化
12.
A spring on the valve stem tends to hold the valve on its seat (closed). The lower end of the spring rests against the cylinder head.
气门杆上的弹簧使气门保持在气门座上(关闭状态)。弹簧的下端抵在气缸盖上。
13.
"There are three types of coil-spring front suspension. In one, the coil spring is located between the upper and lower control arms, and the lower control arm has one point of attachment to the car frame."
有三种螺旋弹簧前悬挂结构:一,螺旋弹簧安装在上、下控制臂之间,下控制臂的一端与车架相连;
14.
Align the bushing with the spring eye or shackle eye and tighten the nut at the socket wrench end of the threaded roTighten until the bushing is forced into the spring eye.
将衬套对准弹簧眼或U型钩眼，并在螺纹杆的套筒板手末端锁紧螺帽。锁紧直到衬套进入簧眼。
15.
Place the cover onto the spring with the internal guide on the cover positioned inside the end coil.
将阀盖及阀盖上的内部引导放置在弹簧上，定位内部端线圈。
16.
Thermal effect on equivalent spring constants of double-clamped beams with different mass arrangements
不同质量块布局双端固支梁的等效弹簧系数的热效应(英文)
17.
Error Analysis of Calculation Methods on Load and Deformation for Diaphragm Spring
膜片弹簧大端载荷与变形特性计算方法的误差分析
18.
spring bow (drawing instruments)
弹簧圆规（绘图仪）