1.
The Performance of a beam pumping unit with incremental, stroke is influenced by the linkage dimensions of the cross double rocker mechanism.
增程式游梁抽油机交叉双摇杆机构的杆件尺寸影响整机性能。
2.
Measurement of Key Dimensions of Large-size and Thin-wall Pieces Based on Vision Inspection Technology;
大尺寸薄壁零件关键尺寸的视觉检测
3.
Modular units for machine tool construction--Spindle noses and adjustable adaptors for multi-spindle heads --Dimensions
GB/T3668.10-1983组合机床通用部件多轴箱主轴端部和可调接杆尺寸
4.
Eventually closed all the screw compressor assembly drawings, plans and dimensions of all the main components map.
最终形成全封闭螺杆压缩机总装配图、形尺寸图和各主零件图。
5.
Basic type and size of fixings for passenger hand-rails in buses
GB/T12430-1990客车乘客扶手杆的固定件基本型式与规格尺寸
6.
modular and dimensional co-ordination concept
构件式组合及尺寸配合
7.
Dimensional tolerances for castings
GB/T6414-1986铸件尺寸公差
8.
Raw Casting basic dimensions, in.,Over,Up to & including
毛坯铸件基本尺寸,英寸,大于,至
9.
Spherical plain bearing rod ends-Boundary dimensions and tolerances
GB/T4222-1991杆端关节轴承外形尺寸和公差
10.
Spherical plain bearing rod ends-Boundary dimensions
GB/T9161-1988杆端关节轴承外形尺寸
11.
Study on the oblique wedge-like transformer with a large dimension rectangular gradual section
大尺寸矩形变截面斜楔型变幅杆研究
12.
Then this set was used to optimize the size of the step struts to get the highest critical load under a constant volume.
然后利用它在压杆体积保持为常量,并具有最高临界载荷的条件下对截面尺寸进行优化。
13.
Saw positioning by using Step-by-steps the electrical machinery, Precision ball bearing lead screw exported from Germany makes the cutting work pieces more precise.
锯片定位，采用德国进口的步进电机及精密滚珠丝杆，使裁切的工件尺寸更为准确。
14.
To draw up and issue dimensional reports of supplier parts and customer certification for approval.
制作并传递外购件尺寸报告，制作客户要求的零件尺寸报告。
15.
Malleable cast iron pipe fittings--Type size--Dimensions list of pipe fittings structure
GB/T3289.1-1982可锻铸铁管路连接件型式尺寸管件结构尺寸表
16.
NOTICE: The dimensions shown on the attached dwgs for ball are the finished (after final machining) dimensions; your rough machined forging must guarantee these final dimensions.
注：附件球体图纸上的尺寸为机加工后的最终尺寸，你们的粗加工锻件必须保证这些最终尺寸。
17.
Cylindrical worm and wormwheel information of the dimensional data to be given on the drawing
GB/T12760-1991圆柱蜗杆、蜗轮图样上应注明的尺寸数据
18.
Influence of Measurement Deviation Upon Motion Error for Four-Bar Linkage Beating-Up Mechanism
四连杆打纬机构尺寸偏差对运动误差的影响