1.
Study on a Robotic System for Multiaxial Bore Assembling
一种用于多轴孔装配的机器人系统研究
2.
Automatic Precision Assembly System for Hole-peg Compliance Assembly
用于孔轴柔顺装配的自动精密装配系统
3.
Photoluminescence Properties of Mesoporous SBA-15 Materials and Rare Earth Complexes Dispersed in Mesoporous Materials;
介孔SBA-15及其孔内组装联吡啶铕配合物的光致发光性质研究
4.
Hole-punching machines, spotwelding machines, and assembly machines also use point-to-point NC systems.
冲孔机、点焊机及装配机也采用点位数控系统。
5.
A Research on Key Technologies of Hole-Axis Assembling Robot Guided by Visual System;
孔—轴装配机器人视觉制导关键技术研究
6.
The Development of PCD Drill Used for Drilling Composites/Titanium Alloy
复合材料/钛合金装配制孔用PCD刀具的研制
7.
Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block.
在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
8.
T&P relief valve opening - comes standard with special tapping on side of tank.
降温减压安全阀安装孔-作为标准配置,热水器侧面均有特制的安装孔。
9.
Install a 14 mm (1/2 inch) (thread size) air hose adaptor in the spark plug hole.
在火星塞孔安装一个14公厘（1/2英寸）（螺纹尺寸）的空气软管适配器。
10.
The method is also proposed on making thread-hole and bolt in interving concerted process, bolt connection as well.
干涉配合螺接过程中螺孔和螺栓的加工方法以及螺栓的安装方法。
11.
Synthesis and characterization of Schiff base complexes functionalized MCM-41 mesoporous molecular sieves
水杨醛类Schiff碱配合物在介孔分子筛MCM-41上的组装与表征
12.
Study on Schiff Base Lanthanide Complexes Covalently Bonded to Meso-structured Silica
Schiff碱稀土配合物以共价键连接方式组装到介孔块体材料的研究
13.
Decorated with embroidered holes or eyelets.
用绣的孔或孔眼装饰的
14.
40L with test lever and short thermostat for installation directly in available tank tappings.
40L型号安全阀配置测试杆和较短的温控器,用于直接安装在容器安装孔上。
15.
A second method is to furnish the surfaces with hinges and to use an exterior sector with drilled holes for each angle setting.
第二种方法是在翼面上装置铰链，用一个对不同安装角钻有不同孔的外部扇形件与之配合。
16.
By measuring all dimensions associated with bearing, the shim dimension satisfying the requirements of bearing bore dimension was calculated to finally reach the requirements of assembly.
通过测量轴承各相关件的尺寸,计算出满足轴承内孔尺寸要求的垫片厚度,最终达到装配要求。
17.
Simple air metering orifices coupled to the unique balancing regulator provide accurate control of the air-fuel( gas or oil).
简便的空气计量孔板装配在平衡阀的接口上来实现空气-燃气，空气-油的精准控制。
18.
multi-aperture pulse distributor
多孔磁心脉冲分配器